Does Curt A25 Fifth Wheel Hitch Ride in the Center of the Rails on a 2008 Ford F-250 or F-350?

Question

Question:

Curt A25 - does this hitch ride exactly center of the rails?

asked by: John

0

Expert Reply:

Yes, the Curt A25 5th Wheel Trailer Hitch # C16180 will sit in the center of the rails. If you take a look at the diagram I've added you can see where you would need to install the Curt Brackets and Base Rails # C16448-204 on your 2008 Ford F-250 or F-350 and where the center line of the hitch is in relation to the brackets.

expert reply by: Kyle S

0

click to enlarge

Answer 1

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 4

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 5

For an above bed rail kit that fits your 2017 Ford F-250 you can use the B&W Custom Installation Kit w/ Base Rails for 5th Wheel Trailer Hitches #BWRVK2402. These are industry standard rails (ISR) that are compatible with B&W Patriot, Curt,…

view full answer...

Answer 6

There are a couple of options that'll work great with your Lippert Turning Point Pin Box, however one hitch stands out to me more than others. Take a look at the: -Curt E16 5th Wheel Trailer Hitch - Slide Bar Jaw - 16,000 lbs #C16115 This 5th…

view full answer...

Answer 7

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth mentioning…

view full answer...

Answer 8

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 9

I'm assuming your 2024 F-250 has the 6-3/4' bed. If that is correct, the right tie-downs are in fact the #TLF3008 and #TL77CR. TorkLift has accounted for the bed access steps on the 2024 model and confirmed these will fit your truck.

view full answer...

Answer 10

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 11

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 12

Yes you are - all 5th wheel hitches are going to require some type of rails in order to be used. So you'd need #DM8552016-71 for your 2006 Dodge Ram.

view full answer...

Does Curt A25 Fifth Wheel Hitch Ride in the Center of the Rails on a 2008 Ford F-250 or F-350?

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching