Vehicle Fits for Reese Hitch 89002 and Correct Hitch for 2003 Ford F-150

Question

Question:

My son bought a Reese shadow mount 89002 class hitch from a guy that said it would fit a Ford 2003 F-150 and of course it doesnt fit. So, my question is what vehicles does the 89002 fit and which Reese hitch is needed for the 2003 Ford F-150. Thanks for your kind attention to my question.

asked by: JAMES T

0

Expert Reply:

My contact at Reese confirmed that the part 89002 is a ball mount made for a 2-1/2 x 3/4-inch rectangular hitch opening that was for applications only on 1984 through 1995 Chrysler and Dodge minivans. This item fits no Fords at all.

For the 2003 Ford F-150 we offer both rear-mount hitches and front-mount hitches, each shown on their own respective linked pages. For a rear hitch I suggest the USA-made Curt # C14355 and for a front-mount hitch the Draw-Tite # 65025.

expert reply by: Adam R

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 5

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 10

There is a trailer hitch receiver as well as a 4-way wiring harness that fit your 2022 Jeep Grand Cherokee WL; that said, we don't have any way to reference a VIN so you'll need to confirm if you do have the WL, which is the new model of…

view full answer...

Answer 11

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...