Height of Fulton F2 Swing-Up Trailer Jack When Fully Retracted

Question

Question:

Fulton F2 Swing-Up, Wide-Track Trailer Jack, 8" Single Wheel, Sidewind, Bolt-On - 1,600 lbs Item # F1413040134 What is the length of the jack when stand is all the way in. Or at its shortest height. From bottom of wheel to top of the jack.

asked by: David S

0

Expert Reply:

I went out to our warehouse to take a look at the Fulton F2 Swing-Up Trailer Jack # F1413040134 referenced in your question. I measured an overall height with the jack at its shortest position, fully retracted, of right at 25 inches. I have attached an image with this dimension labeled that you can also take a look at.

This is a really nice, corrosion-resistant jack that features an adjustable mount and swivel system to allow for easy lifting and transport. It has a 1,600 pound weight capacity and an outer tube width of 2-3/4 inches. I have also attached a short video demonstration on this jack that you can check out.

expert reply by: Chris R

0

click to enlarge

Answer 1

I am not aware of a bolt-on version of the Buyers Products Weld-On Safety Chain Retainer part #3375471000. However, if all you were wanting to do is mount your safety chains to the tongue of your trailer then you will just simply do so by running a…

view full answer...

Answer 2

A 13 inch trailer wheel is likely going to use 1/2 inch lug nuts. The torque spec is the same for a 13 inch wheel whether it is steel or an alloy wheel; 75 to 85 foot pounds. I have included a picture with a handy chart with torque values for you as…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 5

The Extreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels, #ORJW350D has an overall length of 18".

view full answer...

Answer 6

Yes, the Extreme Off-Road Swing-Up Jack w/ Dual Wheels iItem #ORJW500D will work for your T@B 400 Tear Drop Trailer. It looks like your trailer comes with an a-frame jack. You would need to ensure you have enough space on your tongue to accommodate…

view full answer...

Answer 7

Here is an image I have from the Xtreme Off-Road Swing-Up Trailer Jack #ORJW750D in zinc which will have the same dimensions as the black Jack #ORJW750BD you are looking at.

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

The Xtreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels #ORJW350D does not come with the bearings installed. You can use something like a rubber mallet or a block of wood and hammer to tap them into place until they are flush.

view full answer...

Answer 10

Based on the information I could find for the DICO 45264 is was popular on ShoreLand'r trailers. This would require the Idler Hub #AKIHUB-545-35-G-EZ-K with the Grease Seal #168255TB used instead of the seal included with the hub. We currently do…

view full answer...

Answer 11

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...