Replacement Lower Bushing And Washer For The Ram TJD-7000S Jack
Question:
Our trailer jack quit moving up and down despite being only 5 months old we bought it somewhere else, but they arent helping us. After disassembling it and looking at the parts we have, it looks like the washer and bushing under the horizontal gear that drives the screw have failed. The washer is deformed and the bushing is shattered. The pin that holds the horizontal gear is bent slightly. Looking at a previous post that lists the replacement parts available for this jack, I cant find anything that lists this particular bushing, just the ones the hold the handle in place. Are you aware of a replacement part for this situation, or have we managed to break the one part that is not available?
asked by: Travis L
Expert Reply:
The Replacement Sidewind Gear Kit for etrailer and Ram Square, Direct Weld Jacks - 5,000 or 7,000 lbs
Item # TJD-7000S-GR has the replacement pins in the kit. The washer can just be replaced with any washer that will fit over the shaft. You just want to make sure it is the same thickness as the bent washer. As far as the tube shaft bushing under the horizontal gear, unfortunately we do not currently offer that replacement part. It would require replacing the jack. I recommend going with a Bulldog Square Jack w/ Footplate - Drop Leg - Sidewind - 28-1/2" Lift - 7,200 lbs Item # BD180455. The Bulldog jacks have more readily available replacement parts if needed.
Products Referenced in This Question
Bulldog Square Jack w/ Footplate - Drop Leg - Sidewind - 28-1/2" Lift - 7,200 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 7001 - 8000 lbs
- Sidewind Jack
- 29 Inch Lift
- Weld-On
- With Rectangle Foot
- Bulldog
more information >
Replacement Sidewind Gear Kit for etrailer and Ram Square, Direct Weld Jacks - 5,000 or 7,000 lbs
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Motor and Gear Parts
- Gears
- etrailer
more information >
Product Page this Question was Asked From
Square Direct Weld Jack w/ Footplate - Drop Leg - Sidewind - 28-7/8" Lift - 7,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Fifth Wheel Trailer
- Gooseneck Trailer
- Utility Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 6001 - 7000 lbs
- Sidewind Jack
- 28-7/8 Inch Lift
- Weld-On
- With Rectangle Foot
- etrailer
more information >
Continue Researching
- Shop: Replacement Sidewind Handle and Gear Kit for Bulldog Round Jacks - 2,000 lbs
- Shop: Replacement Sidewind Gear Kit for etrailer and Ram Square, Direct Weld Jacks - 5,000 or 7,000 lbs
- Shop: Replacement Sidewind Handle for etrailer and Ram Square, Direct Weld Jacks - 3K - 7K
- Shop: Square Direct Weld Jack w/ Footplate - Drop Leg - Sidewind - 28-7/8" Lift - 7,000 lbs
- Search Results: bd500156
- Search Results: jack replacement parts
- Search Results: jack bushing
- Search Results: tjd~7000
- Q&A: Inner and Outer Diameters of Gear Set # TJD-7000S-GR
- Shop: Grease Seals 10-36 (pair)
- Article: Trailer Wiring Diagrams
- Video: Choosing the Right Trailer Wiring
- Q&A: Towing a Trailer with Electric Brakes with a Semi Tractor with Air Brakes
- Shop: Trailer Hitch
- Search Results: 44649
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Q&A: Hub And Drum Replacement for 90865 Rockwell Hub and Drum
- Shop: Trailer Wiring
- Video: Titan Trailer Brakes T2385200 Review
- Search Results: 25580
- Q&A: Brake Controller Wiring for Ford E-450 Motorhome
- Shop: Brake Controller
- Search Results: 68149
- Article: How to Choose the Right Trailer Hitch Class
- Shop: Shackle Bolt with Locknut for Double-Eye Springs - 3" Long
- Video: Roadmaster Automatic Battery Disconnect Installation - 2020 GMC Sierra 1500
- Article: Trailer Maintenance Schedule
- Q&A: Recommended Replacement for Atwood Surge Brake Actuator 85778
- Video: Heavy-Duty Trailer Hitch Installation - 1997 Ford F-350 - B&W