What Size are the Set Screws on Ram Gooseneck Trailer Coupler # GCPN-25008

Question

Question:

Can you tell what size of bolts are on the GCPN-25008?

asked by: Perry W

0

Expert Reply:

Ram gooseneck coupler # GCPN-25008 has set screws and a 7/8" diameter pin. The set screws are 3/4"-10 x 2-1/2". It is recommended to use a large crescent wrench to adjust the set screws since they have a square head instead of a hex head like a regular bolt. There is a replacement set available as # SS-34103-BT. The matching set screw nuts are # SS-34103-NT.

expert reply by: Michael H

0

Answer 1

I reached out to the company that builds the Ram Gooseneck Coupler item #GCSQTW-30008 , Pacific Rim International Factory, and was not able to get an exploded parts diagram. I have listed all of the replacement parts below that are available.…

view full answer...

Answer 2

The laws can be a little fuzzy and vary from state to state but it seems like if the trailer couples to a ball then you have to have safety chains. Technically, by using Bulldog adapter #BD0289640300 the gooseneck trailer is no longer coupling to a…

view full answer...

Answer 3

The Convert-A-Ball Multi-Cushioned Gooseneck Trailer Coupler - Round - 30,000 lbs #CG doesn't have a specific torque spec because it is just the inner sleeve. The set bolt torque spec you need would be based on the outer sleeve with the bolts.…

view full answer...

Answer 4

Yes. If you replace the U-bolts used in Air Lift air bags #AL88204 with the bolt as indicated in the instructions it will be compatible with the Curt Curt Double Lock, Flip and Store Underbed Gooseneck Hitch #C615-632. If your truck is a short bed…

view full answer...

Answer 5

Mounting your axle under your leaf springs will lift your trailer more than 7 inches (4 inches for your axle diameter plus 3 inches for the thickness of your leaf springs and spring seat). Since you have a livestock trailer, that would not be the…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 9

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 10

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 11

The Air Lift LoadLifter 7500 XL Air Helper Springs #AL57531 will fit your 2022 Ram 3500 Mega Cab with single rear wheels. This is the extra heavy duty 7,500 lb kit so it is most commonly used on dually trucks, but it will fit single rear wheel models…

view full answer...

Answer 12

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...