Widest Setting of the CE Smith Bunk-Style Guide-Ons for Boat Trailers Part # CE27600

Question

Question:

Your description says that these guide-ons can be adjusted laterally up to 13 inches, but it is unclear exactly what this measurement is. My question is: at the widest setting, what is the lateral distance between the outside edge of the trailer frame and the inside edge or face of the padded bunker?

asked by: Bruce

0

Expert Reply:

I spoke to my contact at CE Smith about the CE Smith Bunk-Style Guide-Ons for Boat Trailers part # CE27600 and they informed me that the distance from the outside edge of the frame rail to the inside face of the bunk board while at its widest setting is 15".

expert reply by: Conner L

0

Answer 1

Yes, you can use the CE Smith Bunk-Style Guide-On Kit #CE27600K90 for the inside pontoons on your cradle lift. You will want to ensure that the uprights will not interfere with anything under your boat when on the lift. The uprights are 19-3/4"…

view full answer...

Answer 2

If there is no flex in the bunks with the pontoon boat loaded, you should be fine with the 1/2 inch clearance. If you are possibly hitting the frame of the trailer when traveling I recommend replacing the bunk brackets with taller ones like part…

view full answer...

Answer 3

For bunk style guide-ons such as #CE27600 the bunk board and boat should only barely touch if at all. There isn't a hard and fast rule that says it should be this many inches. But since guide-ons are not meant to support weight like a regular…

view full answer...

Answer 4

Provided that the widest part of the I-Beam frame is no wider than 3 inches and the overall height no more than 4-1/4 inches you could use CE Smith Bunk-Style Guide-Ons #CE27600 with the I-Beam frame. The fact that the frame is aluminum should not be…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 10

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 11

Thank you for the pictures! For a replacement option I recommend the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout - Bolt On - Disc - 2" Ball - Zinc - 7.5K #DX29FR to replace your current actuator. The #DX29FR has a 7500lb trailer weight…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...