Replacement Dutton-Lainson Trailer Jack 22457 or 22560

Question

Question:

Looking for a replacement trailer jack for a dutton-lainson 203925B.

asked by: Todd

0

Expert Reply:

I spoke to my contact at Dutton-Lainson and was able to confirm that the Pull Pin, Easy Swivel Trailer Jack with 6" Wheel part # DL22457 for 10" lift or part # DL22560 for 12" lift is a direct replacement for the jack you have on your trailer now. For future reference, the part number of the jack is a set of three digits on the black plastic handle. If you add "22" to these digits that will give you the full part number of the jack. The jack you have now should have either "457" if you have the 10" lift version or "560" if you have the 12" lift version stamped into the handle.

expert reply by: Conner L

0

click to enlarge

Answer 1

We did have a customer come back and say that the Fulton jack part #FTJ120W0301 will attach just fine to the pipe mount on the trailer frame where a Shelby jack just like yours was installed.

view full answer...

Answer 2

The direct replacement for your Dutton-Lainson 203925B jack would be part #DL22560. According to Dutton-Lainson, the jack would indeed be compatible with your existing mounting plate. I've linked to a product demonstration video featuring…

view full answer...

Answer 3

Yes, since your current Fulton jack is a bolt-thru style, you can use the Fulton XLT Bolt-Thru Swivel Trailer Jack #F26ZR with your current welded on bracket. You just need to remove the jack from the included bolt-on bracket and mount it to your…

view full answer...

Answer 4

In order to find if the mounting holes on the Swivel Marine Trailer Jack with Caster Wheel - Bolt On - Sidewind - 10" Travel - 1,000 lbs #DL84MR will line up with your existing bracket you will need to take some measurements. See the…

view full answer...

Answer 5

Yes, you are correct. As long as your trailer frame is 3 inches wide across that top and 5 inches tall the Easy Swivel Trailer Jack, #DL22800, will fit on your trailer without drilling. I have posted a photo of a jack with the same mount installed…

view full answer...

Answer 6

We do have some options similar to the Optronics Halogen Utility Light #QH16CTS but a little smaller: - Vision X Utility Market Floodlight #XIL-UF32 (456 lumens and measuring 3-1/2" long x 1-7/8" tall x 7/8" deep) -…

view full answer...

Answer 7

There are some Dutton-Lainson trailer jacks that are made in the USA as well as a few that are not. Any jacks that we carry that are made in the USA have that as part of the description to help set them apart. Currently we have the following…

view full answer...

Answer 8

We do! It looks like you're needing the Rhino-Rack Recovery Track Carrier for Pioneer Platform Rack #RR43159-RMTXMPS which is exactly what you're asking about.

view full answer...

Answer 9

The Round Swivel Marine Jack w/ Wheel - Bolt On - Zinc - Sidewind - 10" Travel - 1,000 lbs #MJ-1206B can absolutely be installed on the tongue part of the trailer. The video you are referring to I have attached and it wasn't added to…

view full answer...

Answer 10

The Dutton Lainson Pull Pin, Easy Swivel Trailer Jack #DL22560 referenced in your question is designed to fit a 2-1/2 inch diameter weld-on mount like what you have installed on your trailer. This jack will work great with your existing hardware…

view full answer...

Answer 11

Based on the picture you submitted the matching trailer jack we have to what you have is the Dutton Lainson part #DL22800. I attached an install video for you to check out as well. At the very worst you may have to use the bolt on brackets that…

view full answer...

Answer 12

The perfect replacement jack that you would need would be the Dutton Lainson Sidewind Jack part #DL22560 that you referenced. It will bolt right up to your mounting bracket and has 12 inches of lift. Check out the review video I attached for this…

view full answer...