Does Kwikee Single Step 28 Have Same Motor as 32 Series

Question

Question:

I have a THOR ACE 27.2 I bent the Kwikee single step frame Series 28. The motor and linkages are OK. Can the frame be replaced with a two step Series 32 frame and use the same motor? Thanks,

asked by: JOE M

0

Expert Reply:

Yes, the Kwikee motor kit from a 28 is the same as a 32 since the part # LC379145 is the kit for both so for just the frame you'd need the part # LC3722618 and it would fit your current motor.

expert reply by: Jameson C

0

Answer 1

The Lippert Components Kwikee Step Frame 32 SERIES DOUBLE STEP (908032000) #LC3722618 is just the frame and is the replacement part you are seeking for your Series 32 steps. It does not include the motor or control switch.

view full answer...

Answer 2

It sounds like you're looking for the Replacement Gear Box and B Linkage for Kwikee Electric RV Steps #LC379161. This includes the gearbox and the linkage so you should be good to go for your Kwikee 28, 31, 37, or 39 steps!

view full answer...

Answer 3

If you're having an issue with the steps fully extending and retracting then that points to the motor. The control box reads the motor's voltage to send the signal to stop the steps so if the motor is not working correctly it will arc…

view full answer...

Answer 4

The distance between the steps of the Lippert Kwikee 32 Series Electric Step #LC3722618 is 7 inches. I attached a picture that shows this dimension and the overall drop too.

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 7

Since you need the Replacement Control Unit for Kwikee 38 Series Electric RV Steps #LC363989 I'm assuming you have 38 series steps on your 2017 Thor Windsport. The correct replacement motor for these steps would be the #LC379147.

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...