Kit Needed to Convert 4-Way of Trailer to 7-Way

Question

Question:

I need to wire a 4way trailer wire into a 7way plug ? All my trucks have a 7 way wiring hookup

asked by: Will

0

Expert Reply:

We have a kit that is designed specifically for converting the 4-way of a trailer to a 7-way. For that you would want the 7-Way Upgrade kit part # HS381-9000 which comes with everything needed.

expert reply by: Jameson C

0

Answer 1

I'm assuming you want to replace everything here so I will start off with a 4-way. I recommend using the Hopkins Endurance 4-Way Flat Trailer Wiring Harness - 30' Long #HM48265. This will give you a lot of wire to work with so you can hook up…

view full answer...

Answer 2

It sounds like you want to tow a pair of trailers in line, and to hook up the lighting you will need to use junction box #38656 along with 4-flat connector #18172, which you can mount with brackets #18144 and #18140. You are going to run the lights…

view full answer...

Answer 3

First you will want to connect an 18 gauge wire to the Temp Sender mounted on your vehicle. You will then route the wire through the firewall into the passenger compartment where the Temperature Gauge is mounted and attach the Temp Sender wire to the…

view full answer...

Answer 4

The only version of the etrailer wiring 7-way upgrade kit part #HS381-9000 that we offer is this one that has the RV wiring colors. The best solution I can provide to help with that is a wiring diagram that has both color setups for you to compare…

view full answer...

Answer 5

We have the part #DW04923-1 which is a jacketed 4-way wiring sold by the foot. All you have to do is enter a quantity of how many feet you need into the quantity box and we'll ship you out that length of 4-way wiring.

view full answer...

Answer 6

A junction box/7-way plug kit like Epicord #277-000141 or #HS381-9000 lets you convert the camper to match the 7-way RV blade type connector format. This avoids the extra connection points and potential trouble spots from using separate adapters.…

view full answer...

Answer 7

There is not a plug and play adapter for your Lance connector that we are aware of. Typically this is installed by the Lance dealer. A junction box/7-way plug kit like #HS381-9000 is an option you have to convert the camper to match the 7-way RV…

view full answer...

Answer 8

The older Lance truck bed campers use a proprietary plug and we don't have an adapter for this. We don't carry it but Lance does offer a matching vehicle side trailer connector for this but I recommend just converting the trailer connector on…

view full answer...

Answer 9

First you will need to remove the old hydraulic equipment. Remove the surge coupler or actuator, remove all the lines, and finally remove the brake assemblies. If you have 10 inch diameter hub and drums, you may need to replace those as well. If you…

view full answer...

Answer 10

It sounds like you may have a 7-way trailer connector and a 4-way trailer connector on your truck and only a 4-way connector on your trailer. Is that correct? See the attached picture for examples of each. If this is the case, then this change will…

view full answer...

Answer 11

Yes, the TorkLift SuperHitch Magnum Trailer Hitch Receiver #TLD1111-30 will fit your 2024 Ram 3500 long bed dually. This hitch fits both the short bed and long bed including dually and single rear wheels. It will replace your factory hitch.

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Kit Needed to Convert 4-Way of Trailer to 7-Way

Product Page this Question was Asked From

Continue Researching