How to Order Custom Length of Jacketed 4-Way Wiring

Question

Question:

What length extension do you offer of a flat four wire harness. Im looking to connect utility trailer to truck with 5th wheel camper between.

asked by: Dale

1

Helpful Expert Reply:

We have the part # DW04923-1 which is a jacketed 4-way wiring sold by the foot.

All you have to do is enter a quantity of how many feet you need into the quantity box and we'll ship you out that length of 4-way wiring.

expert reply by: Jameson C

1

Answer 1

We have a kit that is designed specifically for converting the 4-way of a trailer to a 7-way. For that you would want the 7-Way Upgrade kit part #HS381-9000 which comes with everything needed.

view full answer...

Answer 2

The only version of the etrailer wiring 7-way upgrade kit part #HS381-9000 that we offer is this one that has the RV wiring colors. The best solution I can provide to help with that is a wiring diagram that has both color setups for you to compare…

view full answer...

Answer 3

I'm assuming you want to replace everything here so I will start off with a 4-way. I recommend using the Hopkins Endurance 4-Way Flat Trailer Wiring Harness - 30' Long #HM48265. This will give you a lot of wire to work with so you can hook up…

view full answer...

Answer 4

It sounds like you want to tow a pair of trailers in line, and to hook up the lighting you will need to use junction box #38656 along with 4-flat connector #18172, which you can mount with brackets #18144 and #18140. You are going to run the lights…

view full answer...

Answer 5

First you will want to connect an 18 gauge wire to the Temp Sender mounted on your vehicle. You will then route the wire through the firewall into the passenger compartment where the Temperature Gauge is mounted and attach the Temp Sender wire to the…

view full answer...

Answer 6

While we don't carry that exact part number we do have a replacement hub/drum that would work just as well with the part #AKHD-655-6-EZ-K. This is a 6k hub/drum that fits the spindles of the Timbren Axle Less Kit part #ASR1THDS03.

view full answer...

Answer 7

The RoadMaster 4-Wire Connector #RM-910030-1 has a 1-3/4" center to center spacing for the mounting holes and would require a at minimum a 7/8" wide hole to fit the body of the connector through.

view full answer...

Answer 8

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Answer 9

The Dexter Hub #8-288-3UC1 has 5/8" wheel bolts. For 5/8 inch lug nuts torque them to 175 - 225 foot pounds.

view full answer...

Answer 10

The 2017 and 2018 Toyota Corolla IM are both capable of being flat towed if equipped with a manual transmission. If they have an automatic it will have to be dolly or trailer towed. For a Tow dolly I recommend the Roadmaster Tow Dolly with Electric…

view full answer...

Answer 11

My contact at Ark said the mounting plate for the Ark XO Drop Down Corner RV Stabilizer Jacks #ARK87FR can be installed by modifying it and using countersunk bolts. Attached is a photo of the dimensions for you to reference (117mm long x 72.50mm wide…

view full answer...

Answer 12

The only difference between 7-Way Utility and 7-Way RV is the color of the wires. The pin outs are the exact same so either would work just fine with the other. If you check out the picture I attached you'll see that the functions are all the…

view full answer...

How to Order Custom Length of Jacketed 4-Way Wiring

Product Page this Question was Asked From

Continue Researching