Could Tekonsha 7-Way Harness 118242 Fit 2000 Ford Expedition if Connectors Match

Question

Question:

item 118242 2000 ford expedition.. had existing 4 flat, wiring harness under carriage has 7 wires... down to 4, i listened to the video, it states only used on factory 4 pole harness?? what am i looking for to verify this? and i see 2 quick connects,, is one unused? thank you

asked by: Maryan

0

Expert Reply:

Sounds like your 2000 Ford Expedition is wired for the 7-Way kit part # 118242 to fit. If the two connectors you found match what you see in the attached picture the # 118242 will fit and work well.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Your photo shows the 7-way trailer wiring setup that we call the RV format. The photo I linked shows an actual trailer plug #A10-7W6 like yours and the circuit arrangement is the same as your photo diagram. For reference, the included article…

view full answer...

Answer 2

You can use the Curt T-Connector Wiring Harness, #C55243, or the Tow Ready Replacement 7-Way Harness, #118243, on your 1999 Ford F-250 Super Duty. These are basically the same item for your truck made by different manufacturers. If the price point…

view full answer...

Answer 3

I looked up the owners manual of your 1999 Ford F-350 and found the two fuse locations you are looking for. They are in slots 5 and 6 like you see in the picture I attached.

view full answer...

Answer 4

For your 1998 Ford F-150 Extended Cab with factory 4-way flat, you need the Tekonsha Ford Replacement OEM Tow Package Wiring Harness, 7-Way #118242. This will give you the two additional relays needed as well as the wiring harness. Then you will need…

view full answer...

Answer 5

It sounds like your 1997 F-150 does not have the tow package wiring so the wiring harness #118242 will not work on your truck. To install a 7-Way trailer connector at the back of your truck, you will need to start with a working 4-Way connector,…

view full answer...

Answer 6

I believe the connector you found is the connector you will use to plug in the wiring for your 7-way connector. There should be a wiring connector along the drivers side frame rail at rear of truck between the rear wheel and the rear of truck (see…

view full answer...

Answer 7

On your 1999 Ford F-150 with factory 4-Way flat, the brake controller port is located under the dash close to the center console. It is near the OBDII diagnostic port. I have included a link to a video showing installation of a brake controller that…

view full answer...

Answer 8

Since your 1999 Ford F-150 has a factory 4-way, and have the correct plug-in wiring adapter #3035-P (plug one end of adapter into your brake controller #5504 and other end into the built-in harness beneath your dash). Based on what you referenced you…

view full answer...

Answer 9

It looks like you are looking for a replacement trailer connector for your 1999 Ford F150 pickup truck. The Tow Ready Replacement 7-Way Wiring Harness, part #118242 is an exact replacement for the OEM harness. To install the harness you will need to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 12

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...