Replacement Lift Brackets and Chains for a Reese 15,000 Pound Weight Distribution System

Question

Question:

Yes I have a reese 54970 15,000 pound away bar set up but in missing the snap up brackets and chains can u guy direct me to what I need?

asked by: Michael B

0

Expert Reply:

Since your Reese weight distribution system is rated for 15,000 pounds I recommend getting 2 of heavy duty lift bracket # 58392. For a chain kit use # 3216. You would only need 1 chain kit.

expert reply by: Michael H

0

Answer 1

Yes, the u-bolts from the Reese Replacement Chain Kit #55630 are the same size as the Reese Replacement Weight Distribution Chain Kit #3216. Both of the u-bolt sizes are 3/8 inch.

view full answer...

Answer 2

Each of the two 9-link chains included in the Reese Replacement Weight Distribution Chain Kit #3216 measures 13-inches tip to tip. Reese no longer makes an 11-link replacement chain, but you can use the Curt #C17111 kit.

view full answer...

Answer 3

The chains in the Reese Strait-Line Hitch with Shank 1,200 lbs. TW / 12,000 lbs. GTW, item #RP66084, are designed to be used with weight distribution systems up to 12,000 pounds gross trailer weight and 1,200 pounds tongue weight. These chains can be…

view full answer...

Answer 4

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

An underslung trailer coupler is one that attaches to the bottom of the trailer frame and an overslung one is one that attaches to the top of the frame. Measuring is not required if you just take a look at your coupler and see where it attaches to…

view full answer...

Answer 10

The Husky Center Line Weight Distribution with Sway Control 32217 is for 600 lb to 800 lb total tongue weight capacities (the tongue weight of your fully loaded and ready to go trailer plus the weight of any cargo behind the rear axle of your tow…

view full answer...

Answer 11

Yes, we sure do! I recommend our own branded etrailer Trailer Hitch Receiver #e79AR. This has the common 2" opening for many accessories and ball mounts. It is coated in our matte black finish so that it blends in well with the OEM appearance…

view full answer...

Answer 12

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...