Seal # RG06-050 Recommendation for a Hub with Bearing # L68149

Question

Question:

I am replacing the bearings on my 1995 travel trailer. It has dexter axels and bearing L68149, and race L68111, the seal does not have a part number on it, can you cross reference this seal for me.

asked by: Todd

0

Expert Reply:

I did some research and based on the bearing and race number that you gave me you have # 84 spindle that will need Grease Seals # RG06-050.

I attached a couple videos on bearing replacement that you should find informative.

expert reply by: Jameson C

0

Answer 1

Hey Jon, so the Bearing Buddy seal kit part #BB60002 that you referenced is the correct fit based on your bearing numbers.

view full answer...

Answer 2

You will need the Spindle Grease Seal Set #BB60002 for your 3,500LB axle and the Inner Bearing #L68149. This kit will fit on before the inner bearing and will work with your Bearing Buddy Model 1980 #BB24SR. Be sure to get 2 kits if you have tandem…

view full answer...

Answer 3

We do have Bearing Buddies that would fit the 1.980 inch diameter hub bore used by the #AKHD- 655-35-K hub/drum. I'd recommend the stainless steel version, part #BB1980A-SS. For the Bearing Buddy seals, use #BB60002. Unfortunately, the…

view full answer...

Answer 4

We carry grease seals, bearings, races, grease caps and all similar items for a variety of trailers. Please note that trailer makers typically do not maintain specs for items like seals used in their trailers so knowing the trailer year/make/model,…

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

From the numbers you provided it sounds like you need replacement grease seals. In my research, the grease seals I found with the GS-1719DL number have a 1.72 inside diameter and 2.565 outside diameter. The replacement double lip grease seals you…

view full answer...

Answer 7

Thank you for providing all the information. If you are going to replace your entire idler hub you would want the Stainless #KH84545S or Galvanized #DE36VR idlers hubs since its on a boat trailer. These will come with the Inner Race #L68111 and Outer…

view full answer...

Answer 8

In order to replace the Dexter 023-359-00 left hand and 023-360-00 right hand braking assemblies you will want to use the Dexter Nev-R-Adjust Electric Trailer Brake Kit part #23-464-465 which will replace both sides and it's a direct bolt-on…

view full answer...

Answer 9

The magnets between differing trailer brake assembly capacities aren't more powerful than each other so much as they are different in sensitivity. You don't gain any power going with a higher rated assembly than you need. You actually just…

view full answer...

Answer 10

To help you with replacement drums and brake assemblies, I need more information on your 2011 Keystone Outback 260FL. I need to either know the bearing numbers and seal number or know a few spindle dimensions. The bearing numbers can be found by…

view full answer...

Answer 11

Hey Rob; thanks for the photos and it was actually the one with the hub number that did it. That's a BD 545 which is an AxleTek 3,500 lb hub and drum like the Trailer Hub and Drum Assembly #AKHD-545-35-K. The 35 on the axle sticker was a good…

view full answer...

Answer 12

Yes, the replacement awning fabric part #LCV000334382 that you referenced will replace the fabric of your current 14 foot long awning that you have from Solera.

view full answer...

Seal # RG06-050 Recommendation for a Hub with Bearing # L68149

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching