Does Wiring Harness 118509 Fit 2008 VW Touareg Without Factory Trailer Connector?

Question

Question:

Thanks so much for the detailed response - instead of running the power wire all the way to the front, can I simply use the 12v socket in the boot area when I'm towing? Thanks

asked by: Ed

0

Expert Reply:

Yes, I can confirm for you that the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118509 is a fit for a 2008 VW Touareg without a towing package. This harness will give you a 4-flat connector for use at the back of your vehicle.

I have added links to a video review and install, as well as the instructions for you to take a look at.

expert reply by: Kyle S

0

Ed

6/16/2018

Thanks so much for the detailed response - instead of running the power wire all the way to the front, can I simply use the 12v socket in the boot area when I'm towing? Thanks

Reply

Kyle S.

6/16/2018

When installing Wiring Harness # 118509 you cannot use the 12V socket in the boot area of your '08 Touareg, you will need to run the power wire to the battery. The reason you need to run it to the battery is that will eliminate the power draw on your VW's electrical system; using the accessory 12V socket you asked about was not designed to handle the additional load of a wiring harness and could ultimately fail.

Reply

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 4

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 7

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 8

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 9

Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Does Wiring Harness 118509 Fit 2008 VW Touareg Without Factory Trailer Connector?

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching