Recommended Plastic Fender for 14 Inch Wheel and Tail Lights

Question

Question:

White plastic Whitney ligot for 14 inch Plastic fendre

asked by: Yvon P

0

Expert Reply:

We have white plastic fenders that will fit your 14 inch wheel. I recommend the Plastic, Single-Axle Trailer Fender w/ Top and Side Steps # PF11X35W. If you want matching fenders, then you want # PF11X35W-2. If you need the mounting brackets, I recommend the Galvanized Steel, U-Shaped, Bolt-On Brackets for Plastic, Single-Axle Fender # PF1135-BKT-2.

These don't have the integrated lights, but trailer lights are an easy addition. I recommend the Miro-Flex LED Trailer Tail Lights - Submersible # STL28RB & # STL29RB for this application. If you prefer round lights, then I recommend the Low Profile LED RV Tail Light - Stop, Tail, Turn, License Plate - 10 Diodes - Driver Side # RVSTL11 and # RVSTL10 for the passenger side.

expert reply by: Jason S

0

click to enlarge

Answer 1

The Single Axle Trailer Fenders w Mounting Brackets - White Plastic - 13" to 15" Wheels #PF11X35W-2 comes with the mounting brackets to stabilize the fender. You do not need to drill into the backing for that installation. If you choose to…

view full answer...

Answer 2

Trailer fenders are sized according to the diameter of the trailer wheels. The Fulton #F008543 fenders you'd looked at are for a 13 inch wheel, so I'll assume that's what you have. If your wheel diameter is different, let me know. I'd…

view full answer...

Answer 3

We definitely have a few options available to replace you current fenders, but if you are looking for the most solid one, the Redline Single Axle Fender #PF11X35W-2 will be the best. This will attach to the frame with included brackets, but something…

view full answer...

Answer 4

The 2-Leaf Slipper Spring w/ Radius End for 1,000-lb Trailer Axles #SP-177275 are going to be the closest to what you have. Depending on the exact location your red string in relation to the end of the radius spring this may account for some of the…

view full answer...

Answer 5

Thanks for the photo. Honestly 5 inches of clearance from the fender to the top of the tire is fine if that is what you desire. We normally recommend 4 inches to allow for the suspension travel whether with leaf springs or torsion axles to allow…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 11

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...