What is Backing Plate and Door of Valterra City Water Inlet and Hatch A01-2000BKVP Made Of

Question

Question:

Is the overall construction backing plate and door metal or plastic?

asked by: Tim

0

Expert Reply:

The backing plate and door for the Valterra City Water Inlet and Lockable Hatch for RVs # A01-2000BKVP is made of plastic.

expert reply by: Jameson C

0

Answer 1

If you didn't have a battery used with your breakaway system there'd be nothing to power the brakes in the event of a disconnect so you couldn't use just a switch like the part #FA80-00-2040 by itself. You'd instead need to use a…

view full answer...

Answer 2

Yes, the Galvanized Steel Plumbing Vent, #V2084 will fit PVC pipe with an OD of 1-1/2".

view full answer...

Answer 3

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 4

On this page (typically below the product links) there is a helpful link section that will have the install instructions fo the Hopkins Breakaway kit part #20400 that you referenced. I also attached an install video that shows the kit installed as…

view full answer...

Answer 5

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 6

When wiring a trailer connector, it is best to wire by function, as wire colors can vary. We have an excellent wiring diagram on our website, I will provide you a link so you can look at it. If you are looking at the inside of the trailer connector…

view full answer...

Answer 7

You have it right so far, the 4-way connector is just as you have stated. Remember that Yellow has a L in it so that is the left side brake/turn signal and green has a R in it so that is the right side brake/turn signal. The colors for wiring a 7-way…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Answer 10

I have added a photo detailing the wiring connections for the Pollack Heavy-Duty, 7-Pole, Round Pin conncetor, #PK11700, see link. This is a SAE J560 compliant connector. The wiring diagram for the vehicle side connector, #PK11720, is pictured also.…

view full answer...

Answer 11

We have a online diagram that will help you understand how the break away system is wired into your trailer. It is actually a simple installation. The system splices into the existing trailer wiring. The break away box will have 3 wires coming out of…

view full answer...

Answer 12

Trailer wiring generally uses 16 gauge wire, part #16-1-1. However, with a long trailer like yours you may want to go with a larger like 14 gauge #DW07550-1 or even 12 gauge #12-1-1. Each size is sold by the foot. You will need to have the lights at…

view full answer...

What is Backing Plate and Door of Valterra City Water Inlet and Hatch A01-2000BKVP Made Of

Product Page this Question was Asked From

Continue Researching