Why Dont 2,000 Lb Trailer Axles Comes with a Brake Mounting Flange

Question

Question:

Hello, I’ve been searching a lot for this and can’t seem to find what I’m looking for. I’m trying to find a 2000lb axle with a 58” spring Center that has trailer brake flanges. It’s for a 5x8 trailer that I want to tow with a small vehicle and need brakes. I know I could have brake flanges welded on but it would be much easier if I could by it already welded. Just curious if there is a company that sells them ready to go. Thank you!

asked by: Tyler

0

Expert Reply:

A 2,000 lb trailer axle like the Dexter Trailer Axle Beam part # T20BTR-7258 is not going to come equipped from the manufacturer with a brake mounting flange because of the weight of the trailer it is designed to be used on. However, most qualified welders can add the brake mounting flange part # 4-34 for a very small fee.

The Dexter Trailer Axle has a 2,000 lb weight capacity, 58" spring center, and 72" hub face length. It uses a L44649 bearing on both the inner and outer seats. Once the brake mounting flange is welded to the axle you can then use part # AKEBRK-2 for the braking assemblies and part # AKHD-545-2-EZ-2K for the hub/drum.

In order to complete your electric brake setup you will also need trailer wiring like part # HS381-9000, a breakaway kit like part # 20099, and a brake controller like part # 90885. I have attached a review video on all of the above items for you as well.

expert reply by: Conner L

0

Answer 1

In order to convert the surge brakes on your Triton Snowmobile Trailer to electric assemblies, you will need the brakes themselves, wiring, a breakaway kit, and possibly hub and drum assemblies if you do not already have them. I have attached a…

view full answer...

Answer 2

The weight rating on the #SP-039275 spring would be 1500lbs per side, with a rating of 3000lbs for both sides. I have included some more information on installing slipper springs, if needed.

view full answer...

Answer 3

Wet bolts like the part #126B2 aren't as important to be used if the bushings are nylon but if you wanted to use them you certainly can.

view full answer...

Answer 4

Most trailer leaf springs will have a bushing in the eyes of the spring. It is interesting that the install video we have for the wet bolt part #126B2 that you referenced does not have a bushing involved at all. In reality all that really matters is…

view full answer...

Answer 5

A brake axle would have brakes, either electric or hydraulic drum or disc brakes while an idler hub would have no brakes. Many times, a tandem axle trailer will have one braking axle and one idler axle. The 3500 lb capacity #35545I-EZ-89 axle you…

view full answer...

Answer 6

The only time that a metal valve stem like part #AM20906 is required is when the psi rating meets or exceeds 100 psi. If you plan on using the Kenda 205/65-10 Bias Trailer Tire with 10" Galvanized Wheel #AM3H490 then you don't have to change…

view full answer...

Answer 7

There are a few ways to find the right system for your trailer. The easiest is to look on the trailer axle for a sticker or plate that says what the capacity is. Then you can measure your brake drum to find the right size. I have attached a photo of…

view full answer...

Answer 8

You will need several items to add electric brakes to your Carry-On Utility trailer. Starting with the trailer you will need a hub and drum that matches the bearings and seal on your trailer spindle and your wheel bolt pattern. The only way to be…

view full answer...

Answer 9

Welding a mounting flange, possible item #4-35, is a very precise installation. The flanges need to be installed square and concentric to the hub and drum assembly and each other. If the flange is installed incorrectly rapid brake lining wear,…

view full answer...

Answer 10

You are correct about needing to have a brake mounting flange like #4-34 welded on correctly. Because it needs to be just right it should be installed by a qualified professional in a shop that works on trailers. We do not have specific instructions…

view full answer...

Answer 11

Congrats on your new trailer. To add a brake controller to your 2010 Toyota Tacoma, I highly recommend the Redarc Tow-Pro Liberty Brake Controller item #RED52VR. This is a proportional brake controller that will engage your trailer's brakes when…

view full answer...

Answer 12

Electric brakes do not each have to be changed in pairs, so that would not be the cause of the error message. I am not sure what brake controller you have, but there is some troubleshooting you can do. You will need to find out if the issue is on the…

view full answer...

Why Dont 2,000 Lb Trailer Axles Comes with a Brake Mounting Flange

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching