Recommended Skid Wheels and Placement for a 32 Foot Long 5th Wheel Trailer

Question

Question:

I have a 5th wheel camper that is 391 inches long.. which wheel do you recommend and can it be mounted on the bumper?

asked by: Jim

0

Expert Reply:

For your 32' long 5th wheel trailer I recommend using the Ultra-Fab Skid Wheels for Class A RVs part # UF48-979013. The skid wheels are designed to either be bolted or welded to the trailer frame but can be mounted to the bumper with a bit of ingenuity. The wheels have a 6" diameter and come with built-in zerk fittings.

I have attached a review video of the above wheels for you as well as a sample install photo.

expert reply by: Conner L

0

click to enlarge

Bernie H.

5/25/2020

one of the zerk fittings was sheered off . I am calling on tuesday but i worry about any future problems

Reply

Chris R.

5/28/2020

Without the zerk fitting you won't have easy access to lubricate the wheel, but I don't otherwise foresee any issues with regards to actual operation.

Reply

Answer 1

Yes, that is absolutely normal and is actually mentioned in the installation instructions. To install the MORryde Safe-T-Rail Telescoping RV Hand Rail #MR54BR you're going to need to: -Remove the existing "Lend-A-Hand" rail. Once…

view full answer...

Answer 2

I spoke with a MORryde tech and found that the 36" measurement would be pretty close to the end of the leg adjustment slots but that you would still have 2-4" of adjustability. The issue that you'll run into though is that the first…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The Trailer Hub and Drum Assembly part #AKHD-545-35-K is the correct replacement for an AL-KO 7230. In regards to the braking assemblies, I suggest getting a new pair, the Electric Trailer Brake Kit part #AKEBRK-35-SA. This option will save you some…

view full answer...

Answer 6

Another wire or harness is not needed on the 2023 Honda CR-V for the install of the Curt 4-Way Wiring Harness #C56370, but you do have to add 20 amp fuse to location #17 in the fuse box.

view full answer...

Answer 7

Hello Gaby. I reached out to the manufacturer and found out that the UltraFab Weld-On Jumbo Steel Roller #UF48-979023 uses a 6-1.0mm Zerk fitting. For a replacement you can use the following: - Replacement Brass Grease Zerk for Weld-On Hinges - 6 mm…

view full answer...

Answer 8

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 9

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 10

The spring hanger placement is going to be determined by your axle spacing. For example, if your axles are spaced 33 inches apart, as shown in the attached diagram, a 7K axle slipper spring, like #e74SR, requires a distance of 28-1/2 inches between…

view full answer...

Answer 11

I attached a picture that shows the proper position of shackles and equalizers on trailer suspension. Sometimes the shackle will flip up but if you jack up the trailer by the axle that's got the shackle flipped you can usually get it to flip back…

view full answer...

Answer 12

For your application there really is only going to be a weld on solution that's reasonable like the part #UF48-979022 that you referenced. The frame dimensions are unknown so a weld solution would be better since that really doesn't matter.…

view full answer...