Recommended Junior Locking Paddle Latch for 3/4 Inch Plywood Mount

Question

Question:

I am looking for a locking paddle latch junior sized that is designed to be mounted in 3/4inch plywood. I am having trouble locating such a product. Please help.

asked by: Michael R

0

Expert Reply:

For your "Junior" Locking Stainless Steel Flush Door Latch, I recommend # L1883 which can be mounted in 3/4 inch plywood. The mounting holes are 3 inches center on center vertically and 3-1/4 center on center horizontally or vice versa depending on your mounting preference. The mounting hole must be 2-3/4 x 3-3/4 inches.

expert reply by: Jason S

0

Answer 1

The Locking Stainless Steel Flush Door Latch, #L1883, has a threaded hole on the inside part in which you could insert your own knob so that it can be easily opened from inside. Another option is basically the same door latch that comes with the…

view full answer...

Answer 2

There is an indention in the bracket over the latch on the "Junior" Non-Locking Steel Flush Door Latch #N1980 which keeps it from falling out. I have pointed this out in the attached photo.

view full answer...

Answer 3

Unfortunately, there's not a stainless, non-locking version of this latch. However, there's a non-locking version of the "Junior" latch paddle available in steel as part #N1980.

view full answer...

Answer 4

The Greystone Built-in Microwave part #324-000105 is 23-3/8" wide x 15" tall x 13-1/2" deep with the trim kit and 19" wide x 12" tall x 13-1/2" deep without the trim kit. Therefore, the Greystone…

view full answer...

Answer 5

That appears to be the Aluminum Eagle wheel from Lionshead. We currently only carry this wheel in an 8 lug 16" x 7". Our most similar wheel in a 15x6 is the Aluminum Liger Trailer Wheel #LH49FR. This is similar in design and color…

view full answer...

Answer 6

Yes, the Heavy Duty Equalizer Suspension Kit part #K71-360-00 does fit your 2008 Weekend Warrior 300FS that has a triple axle setup and a 35 inch wheelbase.

view full answer...

Answer 7

If the hole in your door for the handle measure 2-3/4" x 3-3/4" the #L4080 would work, but most likely you would need a handle like the part #L1883 as that is more like the latching style of your current handle. This latch installs…

view full answer...

Answer 8

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 9

To get power to the controller of your Solera Smart Arm 12V Power RV Awning part #LC759404, you need to tap into an existing circuit, or run a power wire from the battery with an inline fuse holder, and a 15 amp fuse, like part #SWC9538, and part…

view full answer...

Answer 10

We do have awning power switches with four wires in both black and white, the Replacement Switch Kit for Solera Power RV Awnings part #LC285499 for white or part #LC285500 for black. Please note, if your wire colors don't match you will need to…

view full answer...

Answer 11

The easiest way would be to call your dealer's service department and have them run the VIN of your vehicle. They should be able to tell you exactly how your vehicle was equipped. You could also locate the tow plug connector, which is on top of…

view full answer...

Answer 12

Grease Seal #RG06-050 is the replacement part for the Dexter 010-019-00. It is 1.719 inches inner diameter and 2.565 inches outer diameter. It is a fit for 3500 lb axles. This is a confirmed replacement cross-reference.

view full answer...

Recommended Junior Locking Paddle Latch for 3/4 Inch Plywood Mount

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching