Raised Plates on the Shank of the Curt Adjustable 2-Ball Mount Part # C45902

Question

Question:

RE: Curt 45902 ball mount. Hi, the pictures of this ball mount on your site show a raised area on all 4 sides of the shank, but pictures of the same mount from other places online do not have the raised area. Is one a newer version, or ?

asked by: Mike

0

Expert Reply:

The raised square plates on shank of the Curt Adjustable 2-Ball Mount part # C45902 are present on older versions of the ball mount but not all. The new version of this ball mount has the smooth shank like you have mentioned. The version of this ball mount we carry is the one that has the rounded shank.

expert reply by: Conner L

0

click to enlarge

Answer 1

Yes, the Curt locking pins #C23556 will work great for the Curt Adjustable 2-Ball Mount #C45902. I was able to go out to the warehouse and confirm the fit for you.

view full answer...

Answer 2

The Rock Tamers Heavy-Duty Adjustable Mud Flap System #ERT00110 will fit on your 2-1/2-inch ball mount so long as you have at least 1-inch of available space (as shown in the linked diagram). In terms of the exhaust you will want to use either the…

view full answer...

Answer 3

I suggest using heat shields #RT76FR with the rock tamers #ERT00108 unless you have an aftermarket tip on your exhaust that makes a complete 90 behind the tire.

view full answer...

Answer 4

The Rock Tamers Adjustable Mud Flap System, part #ERT00108, offers height, width and angle adjustment to match a range of vehicles. Please note that there must be at least 1-inch of clearance between the back of the ball mount face and the trailer…

view full answer...

Answer 5

We have a heat shield #RT76FR for applications like your 2017 Chevy Silverado 2500 where the exhaust points right at the flap of the part #ERT00108. This would be your ideal solution and would work well.

view full answer...

Answer 6

For a replacement dual ball for the Curt Dual Ball Mount part #C45902 you'd need the part #C45923.

view full answer...

Answer 7

Yes, the Curt Trailer Hitch Receiver #C15802 does fit your 2022 Ford F-250 Super Duty. This is a class V hitch with a gross towing weight of 20,000lbs and a maximum tongue weight capacity of 2,700lbs. If you need a ball mount, a great option is the…

view full answer...

Answer 8

The sway control that you'll need to use with your 20K Curt Adjustable 2-Ball Mount #C45902 for a 2-1/2" trailer hitch is the Tuson Asymmetric Sway Control #335TSC-1000 because it installs on the trailer frame and uses the trailer brakes to…

view full answer...

Answer 9

There are 3 places of possible movement for Curt adjustable ball mount #C45902: the 2 pins that hold the ball to the shank and between the shank and the hitch itself. If you have that screw at the ball part nice and tight then you are probably…

view full answer...

Answer 10

The Ford 2-1/2 inch trailer hitch on your 2005 F-350 does have a different corner radius then what 2-1/2 inch accessories have so there have been some fit issues. But the Curt products such as adjustable ball mount #C45902 didn't seem to be a…

view full answer...

Answer 11

The Tuson Electronic Sway Control System for Electric Trailer Brakes #335TSC-1000 has installation instructions that give a placement location on the center of your trailer and 5-10 feet behind the hitch ball. The unit comes with a wiring harness so…

view full answer...

Answer 12

The Tuson Electronic Sway Control System #335TSC-1000 that you referenced is perfectly compatible with your Curt weight distribution and integrated brake controller of your 2020 Ford F-150.

view full answer...

Raised Plates on the Shank of the Curt Adjustable 2-Ball Mount Part # C45902

Product Page this Question was Asked From

Continue Researching