Compatibility of Curt Locking Pins on Curt Adjustable 2-Ball Mount C45902

Question

Question:

Can you use the Curt Locks - C23556 for this unit?

asked by: Amal J

0

Expert Reply:

Yes, the Curt locking pins # C23556 will work great for the Curt Adjustable 2-Ball Mount # C45902.

I was able to go out to the warehouse and confirm the fit for you.

expert reply by: Jackie C

0

Answer 1

We have a heat shield #RT76FR for applications like your 2017 Chevy Silverado 2500 where the exhaust points right at the flap of the part #ERT00108. This would be your ideal solution and would work well.

view full answer...

Answer 2

The raised square plates on shank of the Curt Adjustable 2-Ball Mount part #C45902 are present on older versions of the ball mount but not all. The new version of this ball mount has the smooth shank like you have mentioned. The version of this ball…

view full answer...

Answer 3

For Curt adjustable ball mount #C45902 the locking pin set is #C23556. The pins don't have an official capacity but technically 5/8 inch diameter solid steel is going to have a capacity much higher than the hitch or vehicle. The hitch pin has a…

view full answer...

Answer 4

Yes, you will be able to use the Curt Adjustable 2-Ball Mount #C45902 with your Rock Tamers on your 2012 Ram 3500. The Curt Ball Mount has two hitch pin holes so use whichever one that leaves a 1 inch gap between your hitch collar and the adjustable…

view full answer...

Answer 5

I suggest using heat shields #RT76FR with the rock tamers #ERT00108 unless you have an aftermarket tip on your exhaust that makes a complete 90 behind the tire.

view full answer...

Answer 6

The Rock Tamers Heavy-Duty Adjustable Mud Flap System #ERT00110 will fit on your 2-1/2-inch ball mount so long as you have at least 1-inch of available space (as shown in the linked diagram). In terms of the exhaust you will want to use either the…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Bill yes, the Brass Tire Sensors for TST TPMS #TST-507-RV-S2 will work great with your TST TPMS for RVs - Color Display - Signal Booster #TST-507-RV-4-C. These sensors were designed specifically to be used with that system as well as the 6 sensor…

view full answer...

Answer 10

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 11

Hi Steve, I totally understand, as those Pro Pride hitches are great but reaaaaaaaal expensive. So we can get you weight distribution, but due to the size your hitch and weight of your trailer, there will be a cost because there are few options and…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Compatibility of Curt Locking Pins on Curt Adjustable 2-Ball Mount C45902

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching