Brake Controller Mounting Location Recommendation for a 2011 Infiniti QX56

Question

Question:

With all the switches and ports on the lower dash, where have people mounted a brake controller on the 2011 QX56? Photos would help.

asked by: Ron

0

Expert Reply:

I would recommend you install it below and to the right of the steering wheel, on the lower dash piece that will be nearest to your right knee. Check out the picture I attached to see this area.

I attached installation instructions as well as an installation video for this product for you to check out also.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The red wire from your Dexter DX2 brake controller #58-8 needs to be wired to the cold side of the stop light switch, which on your 2013 Chevy Silverado corresponds to a light blue wire with a white stripe. This wire should ONLY be hot when the brake…

view full answer...

Answer 2

You'd want to use the 20 amp circuit breaker like #PK54220PL unless your trailer has more than two brake axles. If that's the case you'd want to use the 30 amp breaker #38630.

view full answer...

Answer 3

When installing the Dexter Predator Brake Controller #58-8 in your 2008 GMC Sierra you will want to follow the Dexter instructions and install the specified fuse and self-resetting circuit breaker as indicated. The vehicle manufacturer installs fuses…

view full answer...

Answer 4

The Tekonsha P-3, item #90195, is an excellent brake controller. Your brake controller wiring will be under the dash below the steering column a bit to the left. There is no connector so you will not need an adapter. You will connect the wires…

view full answer...

Answer 5

In order to install the Tekonsha Prodigy P3 Trailer Brake Controller part #90195 on a 2001 Chevrolet Tahoe with factory tow package you'll need the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers part #3025-P.

view full answer...

Answer 6

For your 2007 Tahoe with the factory tow package, the Prodigy P3 brake controller part #90195 is simple to install. You only need to splice the four wires on the controller with those already present under the dash. No additional wiring or harnesses…

view full answer...

Answer 7

The New Body Style now comes with the wires for the brake controller loose underneath the steering wheel off to the left, so there is no adapter necessary. All you need to complete your installation is the Tekonsha P-3 Trailer Brake Controller, item…

view full answer...

Answer 8

Beginning with the introduction of the 2007 model year, GM stopped using the connector that was located in the convenience center under the dash for installing a brake controller. Instead, the tow package connection consists of 4 or 5 wires bundled…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...