Installing a Prodigy Brake Controller on a 2007 Chevy Tahoe

Question

Question:

I have no experience installing brake controllers. I am of average intelligence : How easy would it be for me to install a prodigy brake controller on a 2007 Tahoe with factory tow package? Thanks.

asked by: Daniel

0

Expert Reply:

For your 2007 Tahoe with the factory tow package, the Prodigy P3 brake controller part # 90195 is simple to install. You only need to splice the four wires on the controller with those already present under the dash. No additional wiring or harnesses are needed for the brake controller.

The Prodigy P3 Brake Controller is one of our most popular brake controllers, and with our informational videos and the instruction sheets, you should have no trouble at all installing the unit in your Tahoe.

For your reference, I will attach some additional information below.

expert reply by: Renee B

0

Answer 1

The New Body Style now comes with the wires for the brake controller loose underneath the steering wheel off to the left, so there is no adapter necessary. All you need to complete your installation is the Tekonsha P-3 Trailer Brake Controller, item…

view full answer...

Answer 2

In order to install the Tekonsha Prodigy P3 Trailer Brake Controller part #90195 on a 2001 Chevrolet Tahoe with factory tow package you'll need the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers part #3025-P.

view full answer...

Answer 3

The Tekonsha P-3, item #90195, is an excellent brake controller. Your brake controller wiring will be under the dash below the steering column a bit to the left. There is no connector so you will not need an adapter. You will connect the wires…

view full answer...

Answer 4

You have the newer LED version of the Furrion Vision S Wireless RV Observation Camera System w/ 3 LED Marker Light Cameras #FR98NR which has four wires instead of the old three wire system. If you're replacing a running light you will wire the…

view full answer...

Answer 5

Beginning with the introduction of the 2007 model year, GM stopped using the connector that was located in the convenience center under the dash for installing a brake controller. Instead, the tow package connection consists of 4 or 5 wires bundled…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Sure thing, I will go ahead and list out what you need for your 2023 Kia Sportage to add a 7-way for a brake controller so you can tow with the Curt Trailer Hitch Receiver #C94WR: - T-Connector Vehicle Wiring Harness with 4-Way Flat Trailer Connector…

view full answer...

Installing a Prodigy Brake Controller on a 2007 Chevy Tahoe

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching