Compatibility of T-Fitting for 1/4 Inch Air Lines

Question

Question:

Is the T-Piece for 1/4" Air Lines compatible with plastic lines as it is metal?

asked by: Joe

0

Expert Reply:

The Air Lift Union T-Piece for 1/4" Air Lines # AL21838 is metal just like the Firestone # F3025-1, but it is designed to work with the plastic 1/4 inch diameter air lines like # AL22007 or # F2012.

I recommend using a Tubing Cutter like # AL10530 to ensure accurate cuts to prevent leaks at the fittings from crimped or crushed plastic tubing.

expert reply by: Jason S

0

Answer 1

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 2

Hey Tarek, for your 2023 Ford Raptor I recommend checking out the Timbren Suspension Enhancement System #T75MR. This suspension enhancement system has a load leveling capacity of 3,000 lbs, will increase stability while reducing sag, and will install…

view full answer...

Answer 3

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 4

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 5

My contact at Yates Rubber advises that a nominal 8-inch keel roller does not measure exactly 8 inches; typically they are slightly smaller than the specified size, much the way a piece of 2 x 4 lumber is not exactly 2-inches by 4-inches. I took…

view full answer...

Answer 6

For a standard replacement equalizer for your Dexter 13-122 equalizers you'd want the #TREQE1 or for a cushioned version you'd want the part #K71-653-00 which comes with new shackles and bolts. For a kit that includes new bolts, bushings, and…

view full answer...

Answer 7

If the two 6 volt batteries were wired in series to produce 12 volts total then a 12 volt battery would easily work as a replacement for them. If the two batteries were wired in parallel and the output voltage is 6 volts then no. I attached a diagram…

view full answer...

Answer 8

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 9

Based on the photo and information you provided, I can tell you have 12 x 2 inch Dexter brake assemblies for 5.2K axles, for which the Electric Trailer Brake Kit #AKEBRK-7-SA will be an excellent replacement. These are self-adjusting brakes so they…

view full answer...

Answer 10

The brake assemblies you have are 7k Dexter assemblies that are 12 inch by 2 inch in size. The part number #AKEBRK-7-SA will work as a great replacement set. This includes assemblies for both sides of your trailer that are self adjusting.

view full answer...

Answer 11

I believe you are referring to the XTRM Universal Sealant #34427034145-1. If so, it can absolutely be used in place of the original XTRM 100 that was on your roof. This will work just as well as the original sealant and its weather-resistant formula…

view full answer...

Answer 12

The LaSalle Bristol XTRM Self-leveling Sealant part #34427034145-1 is very comparable to the Dicor 501LSW self leveling lap sealant. I can't say exactly what the formula is for Dicor but I can tell you that LaSalle Sealant is a silicone sealant…

view full answer...

Compatibility of T-Fitting for 1/4 Inch Air Lines

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching