Does Backing Plate e96RR Hole Pattern Match Erickson ATV E-Track Tie-Down Kit EM09160

Question

Question:

Hello, Does the hole pattern of e-track backer item # BPEZ match the hole pattern of e-track chocks item # # EM09160? Thanks.

asked by: Larry L

0

Expert Reply:

Yes, the backing plate # e96RR has a hole pattern that matches that of the Erickson ATV E-Track Tie-Down Kit # EM09160 as well as other Erickson E-Track items.

Depending on the diameter of mounting hardware you choose the holes may need minor reaming with a drill.

expert reply by: Adam R

0

Answer 1

It looks like each chock and strap from 2 of #EM09160 will need to be able to hold around 375 pounds to handle the weight of the 2014 Arctic Cat Wildcat X Limited and that is just static load and does not include the forces applied to the chocks…

view full answer...

Answer 2

Typically for wood floors we recommend using backing plates like the part #e96RR with the E-tracks like part #E19148 that you mentioned. I attached an install video for an E-track that shows the backing plate being used as well.

view full answer...

Answer 3

You will need the NOCO Speed Charger #NOC23RR to charge the NOCO Boost Plus Jump Starter #329-GB40. You can use the USB-MicroUSB included with your NOCO or we have a Scosche SyncAble HD Micro USB Cable #332-HDEZ4 which is 4' long you can use…

view full answer...

Answer 4

Yes the Erickson ATV E-Track Tie-Down Kit w/ Ratchet Straps and Wheel Chocks #EM09160 can be installed with lag bolts. It's really up to the application and your best judgment on how best to install this kit and lag bolts would work just…

view full answer...

Answer 5

The Erickson ATV E-Track Tie-Down Kit part #EM09160 has a 1,500 lb weight capacity as a whole. It's not made for vehicles if that's what you were wondering but rather ATVs and UTVs. If you need to secure a vehicle I instead recommend…

view full answer...

Answer 6

The Erickson #EM09162 E-Chock Wheel Chock will work with vertical e-track, but the chock will sit perpindicular to the e-track, rather than inline as it would sit with standard e-track. The slots in the standard and the vertical e-track are the…

view full answer...

Answer 7

The cost of the Erickson E-Chock Wheel Chocks for E-Track - Powder Coated Steel - Qty 2 #EM09162-2 and the single #EM09162 vary from the manufacturer. We adjust our prices based on the manufacturer to attempt to keep the cost the lowest for all our…

view full answer...

Answer 8

As a pair the Erickson ATV E-Track Tie-Down Kit #EM09160 that you referenced has a 1,500 lb capacity, but if you used two sets of these (gives you a tie down for each tire) you'd have more than enough total capacity at 3,000 lbs.

view full answer...

Answer 9

You would not have to use Erickson ATV E-Track Tie-Down Kit #EM09160 for each wheel on both ATVs. You can do just the rear wheels on each or one in the front and one in the back on opposite sides which another customer wanted to do. If you have 2 per…

view full answer...

Answer 10

The chocks of the Erickson ATV E-Track Tie-Down Kit #EM98CV are designed to be driven over as they are bolted to the floor.

view full answer...

Answer 11

The Erickson ATV E-Track Tie-Down Kit w/ Ratchet Straps and Wheel Chocks - 1,500 lbs #EM09160 has holes that are 4-1/2 inches on center horizontally and 2 inches and 4-1/4 inches vertically. I've attached a photo as you asked to assist as well as…

view full answer...

Answer 12

There is definitely no issue in using 2 sets of the Erickson ATV E-Track Tie-Down Kit #EM09160, one for the back and one for the front, to stabilize your UTV. If you look through the photos that other customers have sent in you can see that some…

view full answer...

Does Backing Plate e96RR Hole Pattern Match Erickson ATV E-Track Tie-Down Kit EM09160

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching