Compatibility of Erickson EM09162 e-Track Mounted Wheel Chock with Vertical e-Track.

Question

Question:

Will this wheel chock fit in the slot of a vertical e-track?

asked by: Shaun H

0

Expert Reply:

The Erickson # EM09162 E-Chock Wheel Chock will work with vertical e-track, but the chock will sit perpindicular to the e-track, rather than inline as it would sit with standard e-track. The slots in the standard and the vertical e-track are the same exact dimensions.

I've linked a product description video featuring the e-track mounted wheel chock.

expert reply by: Mike L

0

Answer 1

That's a fine question. Unlike many things in this world the companies like Kinedyne, Erickson and Cargo Smart all made the tracks the same size! So luckily for us we can use any of the e-track or x-track accessories like the Erickson…

view full answer...

Answer 2

It looks like each chock and strap from 2 of #EM09160 will need to be able to hold around 375 pounds to handle the weight of the 2014 Arctic Cat Wildcat X Limited and that is just static load and does not include the forces applied to the chocks…

view full answer...

Answer 3

Typically for wood floors we recommend using backing plates like the part #e96RR with the E-tracks like part #E19148 that you mentioned. I attached an install video for an E-track that shows the backing plate being used as well.

view full answer...

Answer 4

Zinc plated screws are going to be the best option for use with aluminum to resist galvanic corrosion. This corrosion you are referring to is from two dissimilar metals reacting so you want to use the most similar metals when installing your…

view full answer...

Answer 5

I'd recommend a set of the Erickson ATV E-Track Tie-Down Kit w/ Ratchet Straps and Wheel Chocks #EM09160 for each of your ATVs. I'd run the straps on the wheels of each ATV closest to the front of the trailer if at all possible. The…

view full answer...

Answer 6

The cost of the Erickson E-Chock Wheel Chocks for E-Track - Powder Coated Steel - Qty 2 #EM09162-2 and the single #EM09162 vary from the manufacturer. We adjust our prices based on the manufacturer to attempt to keep the cost the lowest for all our…

view full answer...

Answer 7

The Erickson ATV E-Track Tie-Down Kit part #EM09160 has a 1,500 lb weight capacity as a whole. It's not made for vehicles if that's what you were wondering but rather ATVs and UTVs. If you need to secure a vehicle I instead recommend…

view full answer...

Answer 8

The Erickson ATV E-Track Tie-Down Kit w/ Ratchet Straps and Wheel Chocks - 1,500 lbs #EM09160 does not have a specified rating by the manufacturer. I recommend using 5/16 inch grade 5 bolts that are 1 inch longer than whatever your floor thickness…

view full answer...

Answer 9

Yes, the backing plate #e96RR has a hole pattern that matches that of the Erickson ATV E-Track Tie-Down Kit #EM09160 as well as other Erickson E-Track items. Depending on the diameter of mounting hardware you choose the holes may need minor reaming…

view full answer...

Answer 10

As a pair the Erickson ATV E-Track Tie-Down Kit #EM09160 that you referenced has a 1,500 lb capacity, but if you used two sets of these (gives you a tie down for each tire) you'd have more than enough total capacity at 3,000 lbs.

view full answer...

Answer 11

The Erickson ATV E-Track Tie-Down Kit #EM09160 is intended to secure your trailered 4-wheeled vehicle at the rear tires. The chocks are to be mounted in front of and behind the rear wheels as shown in the linked video and photo. If they were…

view full answer...

Answer 12

It would take an incredibly hard braking situation to lift the rear wheels of a UTV if only the front wheels of it were secured with the Tie Down Kit part #EM09160. Essentially it would only happen if you were in an accident. That being said it is…

view full answer...

Compatibility of Erickson EM09162 e-Track Mounted Wheel Chock with Vertical e-Track.

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching