Erikson Truck Bed Ladder Rack Distance Between Load Stops

Question

Question:

How wide of a load can you fit in between the load stops? Mainly, can you fit a 4ft piece of plywood between the stops or would they need to be taken off?

asked by: Tyler

1

Helpful Expert Reply:

The Erickson Truck Bed Ladder Rack w/ Load Stops - Aluminum - 800 lbs # EM07705 has adjustable load stops that will adjust up to 36.5 inches wide between the uprights. I confirmed this with the manufacturer.

This rack will not allow you to carry a 48 inch (4 foot) piece of plywood unless you put the load stops on the outside of the uprights. I've attached a photo of the underside of the bar to show that this is possible to do. The crossbars are 66-5/8 inches long, so you would be able to find a fit if you position your load stops according to that need.

expert reply by: Jason S

1

click to enlarge

Answer 1

To slide the load stops of the Erickson Truck Bed Ladder Rack #EM07705 past the uprights of the rack you'll need to unbolt the bar from the uprights so that they could slide past. See attached picture.

view full answer...

Answer 2

Yes, it is very likely that replacement key #THKEYN2826 will fit your Voyager XL cargo box with lock 2826. Sometimes with newer keys and older boxes the new key will have to be tapped into the lock to seat all of the way. So if they key doesn't…

view full answer...

Answer 3

The price for the Erickson Truck Bed Ladder Rack #EM07705 includes both of the ladder rack uprights that you see in the main product picture. I attached a review video for this rack for you to check out as well.

view full answer...

Answer 4

I checked with Erickson and loadstops on the bars of the Erickson Truck Bed Ladder Rack #EM07705 add 6 inches to the height of the bars. That means that the overall height of the rack from the top of the bed rails to the top of the load stops will be…

view full answer...

Answer 5

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 6

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 7

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 8

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 9

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 10

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 11

Unfortunately there are no plug-in adapters or harnesses that would allow you to replace the factory 4-way flat trailer connector with a 7-way or a 7-way and 4-way connector on your 2005 Ford F-150. To complete the installation for a brake controller…

view full answer...

Answer 12

I can definitely help you find the correct replacement hub and bearings for your Dexter P-12 SLR axle, but since part of the serial number was unreadable you will need to take a few simple steps to identify which bearings your axle uses. The easiest…

view full answer...

Erikson Truck Bed Ladder Rack Distance Between Load Stops

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching