American Made Trailer Hitch Receiver for a 2000 Toyota Tundra

Question

Question:

Where is this manufactured ?

asked by: George Q

0

Expert Reply:

The Draw-Tite Trailer Hitch Receiver part # 37130 as with all Draw-Tite trailer hitch receivers is made in Mexico. For a trailer hitch made in the U.S.A that is also a confirmed to fit for your 2000 Toyota Tundra, I recommend taking a look at the Curt Trailer Hitch Receiver part # 13184.

The Curt trailer hitch receiver is a Class III hitch with a 2" receiver tube opening. The hitch is rated for use with trailers that have a gross trailer weight (GTW) and tongue weight (TW) rating of up to 5,000 lbs. and 500 lbs. respectively.

I have attached a review video of this hitch installed on a similar 2001 Toyota Tundra for you as well.

expert reply by: Conner L

0

Answer 1

The difference between a 2000 Toyota Tundra with a towable bumper and a non-towable bumper is that the model with the towable bumper will have a cutout in the center of the bumper for a hitch ball wheres the model with the non-towable bumper will not…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Hello Dan, I can definitely help with this. It is completely normal for the Curt TriFlex brake Controller #C24VV to show the current gain setting when the brakes are applied, or when the manual override is pressed. It sounds like you have the gain…

view full answer...

Answer 9

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 12

For your 2024 Hyunda Santa Cruz we have the Curt 7-way kit part #C68JR that is a confirmed fit. This installs by plugging into a factory wiring connector on your vehicle which means a really easy install that doesn't require any splicing.

view full answer...

American Made Trailer Hitch Receiver for a 2000 Toyota Tundra

Products Referenced in This Question

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching