Where to Measure to Determine if Adco SFS AquaShed Cover # 290-46012 Fits

Question

Question:

How do I measure my trailer to fit a cover?

asked by: Karen W

0

Expert Reply:

The measurement for this cover is from the back of the trailer to the front of the trailer including the gooseneck coupler.

As long as your trailer is between 24'7" to 28'6" the part # 290-46012 is going to fit and work well.

expert reply by: Jameson C

0

Answer 1

The best storage cover we have available for the specs you listed on your horse trailer is the Adco SFS AquaShed #290-52253. This cover is technically designed for 5th wheel trailers but it's the only model we have that will fit the 107-1/2"…

view full answer...

Answer 2

The PS-8 screws should work very well going into either material you mentioned. The threads are coarse enough that they'll get good hold on the aluminum or the rubber. For best results, you'll want to ensure that as many screws as possible go…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 6

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 7

Since both a ST145/R12 size tire, like the Kenda Karrier S-Trail #AM10130, and a 5.30-12 size tire, like the Kenda K353 #AM10068, fit a 12 inch wheel, a ST145/R12 size tire can replace a 5.30-12 size tire. Keep in mind that these tires do have…

view full answer...

Answer 8

The difference between load ranges varies based on the tire size and brand. When comparing two tires of the same size and brand, a load range D tire will always have a greater weight capacity and psi rating than a load range C. However, when…

view full answer...

Answer 9

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 10

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 11

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Answer 12

The 12 inch tires that we carry are rated for 65 miles per hour. Any faster than that for extended periods and the excessive heat build up will cause tire failure. To get a tire with a higher speed rating you would have to go up in size. That also…

view full answer...

Where to Measure to Determine if Adco SFS AquaShed Cover # 290-46012 Fits

Product Page this Question was Asked From

Continue Researching