Will Replacement Hitch Bolt and Clip, # Y8890200 Fit a Yakima HookUp Bike Rack

Question

Question:

I have a Yakima HookUp hitch-mounted bike carrier 2 receiver. I think its an older version of the HoldUp carrier, and I am wondering if the replacement hitch bolt and clip you sell for the HoldUp Y8890200 will fit my HookUp carrier. Thank you very much!

asked by: Heather

0

Expert Reply:

I spoke with my contact at Yakima and he stated that the Replacement Hitch Bolt and Clip, # Y8890200, is compatible with your older Yakima HookUp bike rack.

expert reply by: Michael H

0

Answer 1

The good news is the Replacement 2" Hitch Shank for Yakima HoldUp Bike Racks #8880580 is the confirmed correct part from Yakima to convert your HoldUp to a 2" shank. According to Yakima, you're also going to need the Replacement Hitch…

view full answer...

Answer 2

The replacement mounting hardware for the 1-1/4 inch versions of the Yakima HoldUp (2008 to present) is actually #Y8880129. Replacement hardware #8890260 is for HoldUp models that fit 2 inch receivers only.

view full answer...

Answer 3

For your Yakima OnRamp Bike Rack #Y96FR that has the 1-1/4" hitch tube you will need the Replacement Tongue Assembly #Y99TR. This will replace your hitch tube and give you a 2" hitch tube for mounting your bike rack. The Replacement Tongue…

view full answer...

Answer 4

I went and pulled a Replacement Hitch Bolt and Clip for Yakima HoldUp Hitch Mounted Bike Carrier #Y8890200 from our warehouse to measure and found that the bolt has 5/8 inch coarse threads and the size wrench you would need to use to tighten it would…

view full answer...

Answer 5

Yes! We do have those parts for your Yakima SwingBase #Y34VR. The replacement parts you need the Replacement Anti-Rattle Hitch Bolt and Washer for Yakima HangOver Bike Rack #Y52FR (Yakima part 8880953) and the Replacement Hitch Bolt Threaded Insert…

view full answer...

Answer 6

I checked with Yakima and for the Exo Swingbase part #Y34VR the correct replacement hitch pin bolt is the part #Y52FR.

view full answer...

Answer 7

If you are looking for a threaded hitch pin for a Yakima bike rack most likely what you need is the part #Y8890200. The Swagman threaded pin #P5901 would not fit a Yakima bike rack.

view full answer...

Answer 8

The Yakima Quarter ROC bike rack cannot be retro-fitted with the Replacement Hitch Bolt, Nut and Clip, #Y8780022. The bolt and nut are uniquely threaded to work with each other. It sounds like you need to adapt a 2 inch hitch for use with your…

view full answer...

Answer 9

The Yakima HitchLock for Yakima Hitch Mounted Bike Racks - Same Key System (SKS) #Y07235 is the lock you are seeking. It is designed to work with the Replacement Hitch Bolt, Nut and Clip for Yakima Bike Racks and DryDock Load Assist - 2" Hitches…

view full answer...

Answer 10

Sounds like you are looking for a replacement hitch pin bolt #Y8890200 for an older Yakima Roc'N Gate bike rack. The size wrench you would use to install or remove this bolt is 15/16 inch.

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Will Replacement Hitch Bolt and Clip, # Y8890200 Fit a Yakima HookUp Bike Rack

Product Page this Question was Asked From

Continue Researching