Replacement Hitch Pin Bolt Recommendation for Yakima Roc'N Gate Bike Rack

Question

Question:

I am looking for the locking pin wrench for a Yakima Roc series 3 bike rack. Do you carry a replacement? THanks

asked by: Renaldo H

0

Expert Reply:

Sounds like you are looking for a replacement hitch pin bolt # Y8890200 for an older Yakima Roc'N Gate bike rack.

The size wrench you would use to install or remove this bolt is 15/16 inch.

expert reply by: Jameson C

0

Answer 1

It looks like you need replacement hitch bolt, nut and clip #Y8780022. It fits into a 2 inch or 1-1/4 inch shank to provide anti-rattle capabilities of certain present and discontinued Yakima bike racks including the BigHorn, KingPin, BackSwing,…

view full answer...

Answer 2

The Yakima Threaded Hitch Bolts #Y8880131 have a 1/2" -13 thread pitch. I do not see we have any M20 threaded hitch pins or bolts as this is larger than a 3/4" bolt. Most hitch pins are 1/2" or 5/8" in diameter.

view full answer...

Answer 3

For the older Yakima ROC 4 rack the replacement hitch pin you need is the part #Y8890200. I confirmed this with Yakima. For a cable lock you would need to use something like the part #e98891 as Yakima does not offer a solution.

view full answer...

Answer 4

The Yakima Replacement Hitch Bolt and Clip for Yakima HoldUp Hitch Mounted Bike Carrier, part #Y8890200, is a 5/8 inch bolt. The size wrench you would use to install or remove this bolt is 15/16 inch.

view full answer...

Answer 5

We do have what you need but I checked with Yakima for you and the part you mentioned will not work with a Yakima FourTimer bike rack. Instead, there are a couple of parts you that you need, and I verified this with Yakima for you: - Replacement…

view full answer...

Answer 6

I spoke with my contact at Yakima and he stated that the Replacement Hitch Bolt and Clip, #Y8890200, is compatible with your older Yakima HookUp bike rack.

view full answer...

Answer 7

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 8

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 11

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Replacement Hitch Pin Bolt Recommendation for Yakima Roc'N Gate Bike Rack

Continue Researching