Front Hitch for 2017 Winnebago Built on Ford E-450 Chassis

Question

Question:

I have a 2017 Winnebago Minnie, Ford chassis E450. Can you help me with a front bumper hitch set up?

asked by: Sorn C

1

Helpful Expert Reply:

There is a front-mounted hitch that is a fit for your 2017 Winnebago built on a Ford E-450 chassis, the Draw-Tite # 65053. It is a bolt-on installation that comes with the necessary hardware for install.

expert reply by: Kyle S

1

click to enlarge

Answer 1

The Roadmaster anti-sway bar that fits the rear of your 1997 Born free motorhome is part #RM-1139-117. Then for the front use part #RM-1139-115. Both are designed specifially for Class C motorhomes on the Ford E-350 chassis.

view full answer...

Answer 2

Good news, I can help you find a hitch that will fit your 1997 Ford E-350 Bus. The fact that this is a bus means that the cab is a Ford E-350 but the chassis is not the same as the standard van chassis. This means that you will need a bolt-on or…

view full answer...

Answer 3

I have a solution for you that I can provide, but we aren't going to have a custom fit hitch to fit a vehicle like what you referenced. I spoke to my contacts at Curt and Reese and the only styles of hitches that can be made to fit a service body…

view full answer...

Answer 4

Yes we do carry a front hitch that fits your 2014 Winnebago Aspect Ford E450 chassis. For that you'd want the Draw Tite hitch part #65053 which is a confirmed fit.

view full answer...

Answer 5

Yes, you could use the Draw-Tite Front Mount Trailer Hitch Receiver #65053 as a recovery point if you needed it to be. You might also want the tow strap loop for hitches part #MT70029 as well.

view full answer...

Answer 6

The 2015 E450 is only produced as a chassis or a cutaway van chassis, so I assume you're speaking of a RV on a van chassis. The Draw-Tite #65053 is a fit for the 2015 E450. I've confirmed this with Draw-Tite.

view full answer...

Answer 7

The Draw-Tite Front Mount Trailer Hitch Receiver #65053 is confirmed to fit your Sunseeker RV built on the 2014 E-450 but whether or not it will interfere with factory installed stabilizer jacks will really just depend on exactly where they're…

view full answer...

Answer 8

Yes the front hitch #65053 that you referenced is a confirmed fit for your 2021 Thor Outlaw 29j that is built on a E-450 cutaway chassis. I attached an install video for this front hitch on a similar RV as yours for you to check out as well.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...