Amperage Rating of Deka Wire

Question

Question:

What is the amperage rating for this wire - Deka Wire # DW04914-1. Looking into using this in a tow truck led light bar application.

asked by: Mike J

0

Expert Reply:

The Deka Wire # DW04914-1 has six 12 gauge wires and one 10 gauge wire. They are copper wires, and 12 gauge copper wires are rated for 20 amps while 10 gauge copper wires are rated for 30 amps. I've added some video reviews on this product for you to take a look at.

expert reply by: Kyle S

0

Answer 1

The Zinc Shackle Bolt with Locknut for Double-Eye Springs - 3" Long #TRFA73Z916DLNZ is a grade 5 bolt. Your setup as described is a standard setup for leaf spring hangers and double eye leaf springs. The #166081 is made by the same manufacturer…

view full answer...

Answer 2

That is a valid question. We strongly recommend people use 10 gauge wire like the part #10-1-1 (sold by the foot), but we realize that there are a lot of people who get by with 12 gauge wire. There are several variables with trailer brake wiring that…

view full answer...

Answer 3

For bolts that do not have the zerk fittings we have the #007-003-01 you can use and then for never fail bushings you could then use the part #TRBU11566. These parts aren't available in a kit.

view full answer...

Answer 4

I do have some info for you but there isn't a torque spec for shackle bolts like the Shackle Bolt for 1-3/4" Wide Double Eye Springs part #007-003-01. Instead, you'll want to tighten the nut for the bolt until snug and then back it off a…

view full answer...

Answer 5

Thanks for all that info and we can get you exactly what you are needing. Since you have a 2-3/8" axle that would be a 3,500 lb axle, so you want leaf springs rated for that weight. The concern with springs that exceed the rating of your axle is…

view full answer...

Answer 6

For brake assembly wiring, we recommend either twelve gauge wire #12-1-1 or ten gauge #10-1-1 due to the length of the wiring and the amperage required. Both of these options are sold by the foot. You will connect one end to the junction box using…

view full answer...

Answer 7

Thank you for all that info, and replacing the equalizers, as well as upgrading the suspension hardware is going to be the best option for you. The correct size equalizer, as well as the suspension kit that I recommend is the following: - Curved…

view full answer...

Answer 8

If you have a round 3" diameter axle on your Spartan boat trailer then you are going to want to use the CE Smith U-Bolt Kit part #CE23003 which contains u-bolts that are 7" long x 3-1/8" wide x 3/8" diameter. The reason you need…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Amperage Rating of Deka Wire

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching