Erickson E-Track Tie Downs for Mini Cooper

Question

Question:

Can the e track adjustable tire net be used in conjunction with the e track roller idler assembly? The Mini Cooper sits so low to the ground that the idler would make it much easier to operate in an enclosed trailer.

asked by: Richard C

0

Expert Reply:

The Erickson Adjustable Wheel Net with E-Track Fittings # 77314 would not be compatible with the Erickson Roller Idler for E-Track # EM09144 simply because there would be no way to get the straps from the Wheel Net through the Roller Idler because of the E-track fittings attached to the Wheel Net.

I've left links to video reviews of each product for you to take a look at.

expert reply by: Kyle S

0

click to enlarge

Answer 1

Yes, E-tracks are used quite a bit for car hauler applications like what you have so as long as you secure them well like the Erickson E-Track part #EM59150 you'd be fine. We have wheel straps too for E-Track like the part #77314 which would work…

view full answer...

Answer 2

To safely secure your 2018 Mustang Saleen and GT500 I recommend using the Erickson E-Track Wheel Tie-Down Strap #EM58523. This ratcheting tire strap is a perfect solution for your application since it will only touch the tread on the tire and the…

view full answer...

Answer 3

The cost of the Erickson E-Chock Wheel Chocks for E-Track - Powder Coated Steel - Qty 2 #EM09162-2 and the single #EM09162 vary from the manufacturer. We adjust our prices based on the manufacturer to attempt to keep the cost the lowest for all our…

view full answer...

Answer 4

There just isn't a specific distance I can offer for how far apart you should mount the etrailer Horizontal E-Track #e62VR for multiple vehicles. There are way too many variables to give any type of concrete answer for that so you'll have to…

view full answer...

Answer 5

If it were my trailer I would fasten the E-Track to the support beams under the trailer, either the side to side one or front to back ones, by going all the way through those support beams. E-Track like #E19148 is zinc-coated steel and since the…

view full answer...

Answer 6

I checked with Aluma and they list a 14" Liger Wheel and Tire 60-0001396 as a replacement 14" wheel for their trailers but they do not specify the finish. We do have one 14" Liger Wheel item #LH84FR. It is gunmetal gray and has a 5 on…

view full answer...

Answer 7

The etrailer E-Track Roller Idler #e67HR is 3" from the top of the e-track to the bottom of the roller.

view full answer...

Answer 8

We only carry the springs for those heavy duty style ramps. For the springs we have the Ramp Spring - 2K Torque for 1-1/2" Shaft - left hand #RS16933LH and corresponding right hand #RS16933RH. The other parts will need to be either straightened…

view full answer...

Answer 9

The Bargman 7-Way, RV-Style Connector #WG54006-043 referenced in your question uses the standard RV-style pin locations for its 7-Way connector. I have attached a diagram of these locations and their functions for you to check out. Wire colors will…

view full answer...

Answer 10

Yes, the wheel of a motorcycle or bicycle can rest on an e-track no problem.

view full answer...

Answer 11

Based on what we could find, the AL-KO 8490 is a 3,500 lb axle, and your info stating the 5 on 4-1/2" bolt pattern and 10" x 2-1/4" drum size supports that as well. I do recommend verifying what you need by taking apart your current…

view full answer...

Answer 12

Since you have an aluminum trailer I suggest using a tie-down that has a backing plate like #RR5K. This will help reinforce the tie-down since aluminum may not hold up. It would be even better if you can install the tie-downs to the frame of the…

view full answer...

Erickson E-Track Tie Downs for Mini Cooper

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching