Does Trailer Hub Assembly # T4084600042 Fit Spindle TRU94FR

Question

Question:

spindle # TRU94FR T4084600042 Trailer Hub Assembly for 2,000-lb Axles - 5 on 4-1/2 - Cast - T4084600042 Is this right hub for this spindle

asked by: Nick

0

Expert Reply:

The spindle part # TRU94FR is a BT8 spindle which the # T4084600042 is a confirmed fit for. These are also both 2,000 capacity.

expert reply by: Jameson C

0

Answer 1

The installation process of the Lippert Components Bolt-On Shock Kit part #LC281255 will be the same for a single axle trailer and a tandem/triple axle trailer, just repeated. When installing the shocks, you want to point them away from the shackle…

view full answer...

Answer 2

I pulled from our warehouse a piece of Titan Trailer Hub Assembly for 2,000-lb Axles #T4084600042 so that I could measure it for you. I have linked a photo of this 5-on-4-1/2 bolt pattern hub with various dimensions noted, including overall length…

view full answer...

Answer 3

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 4

You can use wet bolts with nylon bushings or bronze bushings. It does not matter which material the bushings are. Also nylon and bronze bushings have about the same longevity.

view full answer...

Answer 5

The pilot hole for your wheel will need to be 4-3/4" or more to be used with Dexter Trailer Hub and Drum Assembly #8-219-13UC3. This is a lug-centric hub which uses lug nuts to secure the wheel to the hub and your wheel will need to have an 8 on…

view full answer...

Answer 6

The recommended clearance with leaf spring suspension on an unloaded trailer is between 2 - 2-1/2 inches. You should have sufficient clearance with your loaded trailer, as leaf springs only tend to deflect 1-1/2 inch when carrying a load.

view full answer...

Answer 7

The typical spring deflection for leaf springs on a trailer is up to 1-1/2 inches when at capacity. The recommended clearance with leaf spring suspension on an unloaded trailer is between 2 - 2-1/2 inches. It sounds like you have a little more than…

view full answer...

Answer 8

Yes, the #84 E-Z Lube Spindle w/ Brake Flange #TRU77FR will fit the 2" schedule 40 pipe.

view full answer...

Answer 9

We usually tell people to look for about 3 inches of clearance to account for the total travel capabilities of trailer suspension. If you have less than 3 inches you might be able to compensate by using slightly longer shackle straps. I have included…

view full answer...

Answer 10

The #TRU77FR spindle accepts a 3 inch axle beam, and the spindle is designed to be welded into place. If the axle tube is painted on the ends, you'll want to take the tubing down to bare metal so you get the proper penetration on your weld.

view full answer...

Answer 11

Thanks for the photo. Honestly 5 inches of clearance from the fender to the top of the tire is fine if that is what you desire. We normally recommend 4 inches to allow for the suspension travel whether with leaf springs or torsion axles to allow…

view full answer...

Answer 12

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Does Trailer Hub Assembly # T4084600042 Fit Spindle TRU94FR

Product Page this Question was Asked From

Continue Researching