What is Recommended Clearance between Trailer Axle and Frame

Question

Question:

I am putting a new 3500# axle spring setup under a 7 x 14 enclosed trailer. It was a torsion setup but I am now using leaf spring uni-216 setup. I have installed the spring to the axle on my shop floor but concerned that I only have 2.5 inches of clearance before the trailer is even on it. I dont want to put the axle below the spring as the trailer will sit too high. Is 2.5inch enough? In the pic the yellow level represents the frame.

asked by: Jeff

0

Expert Reply:

The recommended clearance with leaf spring suspension on an unloaded trailer is between 2 - 2-1/2 inches. You should have sufficient clearance with your loaded trailer, as leaf springs only tend to deflect 1-1/2 inch when carrying a load.

expert reply by: Jameson C

0

click to enlarge

Answer 1

You are correct that for your 2022 Honda Odyssey there are a few different vehicle wiring harness options which can make things a bit confusing. The first two harness we will look at are the Tekonsha #118781 and the Curt #C56382. These harness are…

view full answer...

Answer 2

In terms of the installation procedure, the appearance of the hitch and the weight capacity, the EcoHitch #306-X7372 and the Curt #C64NR Class III hitches are for all intents almost identical. Both the EcoHitch and the Curt are manufactured in the…

view full answer...

Answer 3

There is some trimming of the fascia required when installing on your 2020 Honda Odyssey when you are installing the Curt Trailer Hitch Receiver #C64NR. The only trimming required is a 1.75" x4" section of the bottom appearance…

view full answer...

Answer 4

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 5

Installing a 4,000 lb capacity leaf spring on a trailer with a 3,500 lb capacity axle will make the suspension stiffer which could then in turn minimize the risk of the axle contacting the frame. However, this is not what I recommend to fix your…

view full answer...

Answer 6

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are…

view full answer...

Answer 7

If you look at the backs of the brake assemblies there should be a hole where the magnet wires come out and a little opaque plastic strap. So if you are looking at the back of the assembly and those items are on the left then it is the left side…

view full answer...

Answer 8

The minimum distance between the inside of a tire and the frame rail depends a lot on the setup of the trailer. But as long as the tire and the frame don't touch you would be fine. It's hard to give an exact figure as trailer setups…

view full answer...

Answer 9

In order to pick out the correct springs we need a couple pieces of information. The length of the spring without a load on it and the axle capacity needed. Your springs being totally flat does indicate that you need to replace them but I would…

view full answer...

Answer 10

If you are looking to order a new axle for your 5 foot wide trailer you will need to determine what the hub face to hub face dimension you would need to clear your trailer that is 5 feet (60 inches) wide. You will also need to know the width of…

view full answer...

Answer 11

The spring hangers should be square and you shouldn't have a gap as there is a bushing that should be in the eye of the spring to make up that difference. You may want to consider the Single-Axle Trailer Hanger Kit for Double-Eye Springs -…

view full answer...

Answer 12

It sounds like you are heading in the right direction. To decide where your springs seat will be you will need to mock up your trailer as if you were installing all of the equipment on it. Once you have the suspension part mocked up you will want…

view full answer...

What is Recommended Clearance between Trailer Axle and Frame

Product Page this Question was Asked From

Continue Researching