Adapter Recommendation to Go From Gooseneck Trailer to Fifth Wheel Rails in Truck

Question

Question:

.

asked by: Larry

0

Expert Reply:

So you have a gooseneck trailer and truck with a set of fifth wheel rails installed? Is that correct?

For that we have the part # 16085 which will fit your fifth wheel rails and provide you with a gooseneck ball for the trailer to connect to.

If you have something else going on let me know and I'll see what options we have.

expert reply by: Jameson C

0

Larry

11/7/2017

.

Reply

Jameson C.

11/7/2017

.

Reply

Answer 1

Are you referring to an adapter to tow a gooseneck trailer with fifth wheel rails like the Curt Spyder #16085? If so then yes, the hitch ball is a standard 2-5/16 inch gooseneck ball. If I'm misunderstanding what you're asking, or you…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 4

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 5

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 6

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 7

A wedge is needed, yes, and the Lippert Turning Point pin box does come with a universal wedge, but it is not a very good fit with the B&W Companion #BWRVK3710. So I highly recommend instead using the 5th Airborne Custom Wedge for B&W Fifth…

view full answer...

Answer 8

Most fifth wheel rails are made to the same industry standard dimensions. They aren't all though. If you measure 22 inches on center between the two rails and they look like the rails of the #RP30035 that you referenced they would be the industry…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 12

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth mentioning…

view full answer...