Replacement Hand Knobs for the TracRac Toolbox Mounting Kit

Question

Question:

Can you buy just the knobs for the tool box mounting kit?

asked by: Jay C

0

Expert Reply:

If you are just looking to replace just the knobs on the Toolbox Mounting Kit for TracRac part # TH25200 then you can use the Replacement Hand Knob for TracRac Ladder Rack part # TAKB-90004. These are round knobs and the knobs included in the toolbox mounting kit are more of a triangle shape but nonetheless will still work for you. We do not have the triangle shaped knobs at this time.

The above part is only for the replacement knob, you will also need the threaded stud in order to attach the new knob. Most local hardware stores will have the 3/8"-16 x 2" long threaded stud you will need to attach the knobs to the base rails.

expert reply by: Conner L

0

Answer 1

The Thule knob #853-5714 is not a confirmed fit for the TracRac load stops. The Thule knob will accept an M8 x 1.25 thread pitch bolt and is designed to be used with an M8 x 1.25 x 25mm Carriage Bolt. The bolt on the TracRac load stops is a 3/8 - 16…

view full answer...

Answer 2

The Replacement Knob for Thule Professional Ladder Tilt, #853-5714, will accept an M8 x 1.25 thread pitch bolt and is designed to be used with the M8 x 1.25 x 25 mm Carriage Bolt for Thule and DeWalt Contractor Series Ladder Lift. The replacement…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 7

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 8

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 9

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 10

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...