Thread diameter and pitch for the Replacement Knob for Thule Professional Ladder Tilt # 853-5714

Question

Question:

Replacement Knob for Thule Professional Ladder Tilt What is the thread specification for this knob? Does it match the THULE Stainless Steel T-bolt 853-5648?

asked by: Michael P

0

Expert Reply:

The Replacement Knob for Thule Professional Ladder Tilt, # 853-5714, will accept an M8 x 1.25 thread pitch bolt and is designed to be used with the M8 x 1.25 x 25 mm Carriage Bolt for Thule and DeWalt Contractor Series Ladder Lift.

The replacement knob does not work with the Thule Stainless Steel T-bolt, # 853-5648.

expert reply by: Robert G

0

Answer 1

The Thule knob #853-5714 is not a confirmed fit for the TracRac load stops. The Thule knob will accept an M8 x 1.25 thread pitch bolt and is designed to be used with an M8 x 1.25 x 25mm Carriage Bolt. The bolt on the TracRac load stops is a 3/8 - 16…

view full answer...

Answer 2

If you are just looking to replace just the knobs on the Toolbox Mounting Kit for TracRac part #TH25200 then you can use the Replacement Hand Knob for TracRac Ladder Rack part #TAKB-90004. These are round knobs and the knobs included in the toolbox…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

For a roof rack to be compatible on your 2020 Jeep Wrangler with Sky One-Touch Power Top, it can't be mounted on the top of the roof and it needs to be high enough for the folding roof to clear. What you need are tall gutter-mounted roof racks.…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Thread diameter and pitch for the Replacement Knob for Thule Professional Ladder Tilt # 853-5714

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching