2-1/2 Inch to 2 Inch Reducer Sleeve for Draw-Tite Trailer Hitch # DT45509

Question

Question:

What is the part number for the reducer sleeve that will fit the Draw-tite DT45509 hitch?

asked by: John G

0

Expert Reply:

For a 2-1/2 inch to 2 inch reducer sleeve that fits Draw-Tite trailer hitch # DT45509 use # C45405. I have linked a video review of this reducer sleeve for you.

expert reply by: Michael H

0

Answer 1

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 2

I really wish we had replacement parts still for the Atwood couplers but since they've been out of business for so long we don't have any way to get the parts you are wanting.

view full answer...

Answer 3

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 4

It sounds like you are looking for the replacement key from Reese. Reese is a sister company of Fulton and Tow Ready who is now carrying the Gorilla Guard Coupler Locks #63228 and #63227. Replacement keys are no longer available so replacing the lock…

view full answer...

Answer 5

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 6

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 7

When installing the Tekonsha Prodigy P2 Trailer Brake Controller #90885, we need go back under the dash to find the factory wiring on your truck. Now it's located behind the dash underneath the steering wheel just a little towards the left and a…

view full answer...

Answer 8

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 9

If by serial number you mean VIN and the trailer manufacturer is still in business then yes, you would likely be able to obtain the bearing numbers from the manufacturer. If none of the above are true, then the only other way to determine which…

view full answer...

Answer 10

The amount of bow that's put into trailer axles like the #7359765 is based on about how much a trailer is typically going to weigh that has a 3,500 lb capacity. So there's a bit of approximation and obviously it can't be totally perfect…

view full answer...

Answer 11

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 12

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

2-1/2 Inch to 2 Inch Reducer Sleeve for Draw-Tite Trailer Hitch # DT45509

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching