Is It Okay to Pull Utility Trailer with Slight Spindle Damage?
Question:
Is it OK to drive Utility trailer with the slight spindle damage? Or does the spindle need to be replaced/repaired?
asked by: Kim
Expert Reply:
That is kind of a difficult question to answer without seeing the extent of damage, so I really appreciate the photo. The slight wear on your spindle where the outer bearing is won't be an issue so as long as the spindle is not bent or there isn't further damage. I do recommend taking some sand paper or steel wool and just knocking down any raised edges to ensure you are getting a clean surface to work with. If there is more of a step than what is visually represented when you feel it, then you may want to consider replacing it. If it is just the slight abrasions you won't need to replace it, but you will want to make sure you monitor your bearing grease to ensure no future failure.
If there is more damage than the photo represents, then I've linked the page to your spindle options. You will want to use a digital caliper to ensure the correct replacement and you will want to have a professional welder do the installation as the alignment is extremely important to get right. I've attached a photo to help you with the measurement locations if a replacement is necessary.
Product Page this Question was Asked From
Square #84 Spindle for 3,500-lb Trailer Axles - 1-1/2" Wide
- Trailer Spindles
- Standard Spindle
- 1-1/2 Inch Diameter
- Square
- For 3500 lb Axle
- TruRyde
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 - Pre-Greased
- Shop: Hydraulic Trailer Brake Kit - Uni-Servo - Free Backing - 10" - Left/Right Hand - 3,500 lbs
- Shop: Dexter Hydraulic Trailer Brake Kit - Uni-Servo - 10" - Left and Right Hand Assemblies - 3.5K
- Shop: #84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axle - 1-3/4" Diameter
- Shop: Hydraulic Trailer Brake Kit - Uni-Servo - Dacromet - 10" - Left/Right Hand Assemblies - 3.5K
- Shop: Hydraulic Brake Kit - Uni-Servo - Free Backing - Dacromet - 10" - Left/Right Hand - 3,500 lbs
- Shop: Kenda Karrier ST205/75R15 Radial Trailer Tire with 15" Black Mod Wheel - 5 on 4-1/2 - LR D
- Video: TruRyde Trailer Bearings Races Seals Caps - Bearings - BK1-100 Review
- Q&A: Replacement Driver And Passenger Side Brake Calipers For A 1997 Ranger Boat Trailer
- Search Results: 5 on 5 axle
- Video: Review 2 of Dexter Axle Trailer Axles - Leaf Spring Suspension - 7359765
- Q&A: Front Mounted Receiver for 2018 GMC Sierra 3500 Denali Diesel
- Shop: Front Mount Hitch
- Video: Draw-Tite Max-Frame Trailer Hitch Receiver Installation - 2022 GMC Acadia
- Video: Kodiak Trailer Brakes BH-3MFS-7 Review
- Video: Kodiak Trailer Brakes BH-3MFS-6 Review
- Article: How to Repair an RV Roof
- Q&A: How To Measure And Determine A Replacement Axle
- Q&A: Shifting Trailer Axle Back Into Place After Hitting Curb
- Q&A: Replacement # 84 Spindle Recommendation to Replace a Trailer Spindle
- Q&A: Will Dexter Axle Beam 7359765 Replace Bent 95" Hub Face To Hub Face Dexter Axle?
- Q&A: Weight of Dexter 7359765-EB EZ-Lube 3500 lb Axle
- Search Results: ufp
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Article: 5 Tell-Tale Signs It’s Time to Replace Your Trailer’s Leaf Springs
- Video: Remove, Inspect, and Reinstall Trailer Bearings, Race, and Seals Demonstration
- Search Results: spare tire mount
- Search Results: lug nuts
- Search Results: 3500 axle
- Search Results: ad2527e grease seal
on Trailer Spindles
