Where do the Brown and Red T Connector Wires connect on a 2011 Toyota Sienna

Question

Question:

The instructions do not say where to connect or if to connect at all , the brown and red T connector wires. This is the third T connector set attached to the black box.

asked by: John M

0

Expert Reply:

For installation of the Tow Ready Custom Trailer Wiring Harness, item # 118498, on the 2011 Toyota Sienna, you will need to insert the T-Connector ends with the Green wires and coneectors with Brown and Red wires between the vehicle wiring connectors and tail lights and lock into place on the passenger side.

You will then, Route the T-Connector end with the yellow wire to the driver side behind the panels and along the threshold and connect between the wiring connectors and tail lights on the left side.

I have included a link to the installation instructions for you to review.

expert reply by: Robert G

0

Answer 1

Thank you for your recent purchase of hitch receiver and wiring harness from etrailer. The Curt Wiring Harness #56146KIT is a correct fit for your 2013 Sienna. Thank you for submitting your two photos. This trailer wiring harness installs primarily…

view full answer...

Answer 2

Thank you for the photos! The T-One Vehicle Wiring Harness #118498 you purchased is for a 2016 Toyota Sienna SE, but the connectors you have in your photos look like you have a non-SE model so you'll need the Curt T-Connector Vehicle Wiring…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 10

I definitely understand being a bit overwhelmed by the amount of options in front of you, however I can definitely help with differentiating the trailer hitches for your 2019 Subaru Outback Wagon along with explaining my personal recommendation,…

view full answer...

Answer 11

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 12

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Where do the Brown and Red T Connector Wires connect on a 2011 Toyota Sienna

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching