Availability of Magnet Retainer Clips BP19-001

Question

Question:

where can we get magnet retainer clips BP19-001?

asked by: Joe E

0

Expert Reply:

You can order the Magnet Retainer Clip for Oval Magnet # BP19-001 directly from the product page; one package is a quantity of four clips. These clips are used to replace the magnet retainer clips on oval brake magnets for 10" or 12" electric brake assemblies.

expert reply by: Kyle S

0

Answer 1

The magnet clips #BP19005 should not be making contact with the drum while the brakes engage, so I do not think that is the problem. What I think is going on is it's just not seating all the way. These can get a little squished or deformed…

view full answer...

Answer 2

The #BP19-001 retaining clips are designed to fit the Dexter 7-inch brake magnets. Our contact at Dexter said the BP19-001 will work on both the 7-inch round and the 10-inch oval magnets. The replacement magnet clip, part #BP19005 will fit 10, 12,…

view full answer...

Answer 3

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 4

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 5

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 6

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 7

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 8

I do have an option for you, but we do not carry the Dexter 072-027-00 you mentioned. However we do have the etrailer Double-Eye Spring for 7,000-lb Trailer Axles - 24-7/8" Long #e64SR which will be 3/8" shorter but that is still close…

view full answer...

Answer 9

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and manufactured…

view full answer...

Answer 10

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 11

To replace your WFCO WF-8750P power center I recommend the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K. This 2-in-1 AC/DC distribution panel and converter charger keeps your power systems easily…

view full answer...

Answer 12

You'd need a new panel like the Progressive Dynamics Mighty Mini part #PD4045KA which is the most similar to your Parallax 7345 except is Lithium battery compatible. There isn't a center section replacement available for what you have that…

view full answer...

Availability of Magnet Retainer Clips BP19-001

Product Page this Question was Asked From

Continue Researching