Dimensions of Keepers on Lockable Door Latch

Question

Question:

what are the dimensions of the keepers. I want to install it on the rear door of an old ambulance I use for a tool truck. There is limited room above the door and a light.

asked by: Dean E

0

Expert Reply:

The bottom keeper on Cam-Action Lockable Door Latch Kit # PLR258-002 measures roughly 5-1/8" x 2", while the top keeper measures roughly 3" x 1-3/8". I made a diagram which displays these dimensions, and have also linked a review video for you to take a look at.

expert reply by: Kyle S

0

click to enlarge

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 4

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 5

Hey Jaime, yes you can replace your 25-1/4 inch 3,500 lb axle leaf springs with a 5k rated axle spring like the part #e44SR. This will increase the suspension's weight capacity and might make the ride quality a little rougher but it would fit and…

view full answer...

Answer 6

To create barn doors out of your ramp door, you will need hinges and a latch. I suggest a latch/lock system like the Universal Cam-Door Lock for Enclosed Trailers - 1" Keeper, #383200. This will use a 3/4 inch diameter pipe that you'll have…

view full answer...

Answer 7

Yes, the Dexter E-Z Flex Equalizer #K71-655-00 will indeed work with the standard 1-3/4" wide double eye leaf springs.

view full answer...

Answer 8

We do offer a few of the 7-3/4" long equalizers with 3 9/16" holes. Unfortunately, the standard equalizers in this size like the #TREQE1 are not greaseable. There is the Dexter E-Z Flex Equalizer #K71-655-00 which is a 7-3/4" long…

view full answer...

Answer 9

The only 3-1/8" shackle kit we carry from Dexter is the #K71-358-00 which is for a single axle trailer. If you are in need of a complete kit for a tandem axle trailer, we recommend the MORryde Suspension Upgrade Kit #MR76ZR. This will come with…

view full answer...

Answer 10

I went out to our warehouse to take measurements of the Cam-Action Lockable Door Latch Kit for Large Enclosed Trailers - Zinc-Plated Steel #PLR258-002. The bar you will need is 3/4 inches inner diameter and can be up to 1-1/8 inches outer diameter to…

view full answer...

Answer 11

Yes, you have a couple of ways to test the Dexter DX Series Electric Over Hydraulic Brake Actuator #K71-651. The first test to try is to connect the white wire to the negative post of the battery. Then connect the black wire to the positive post on…

view full answer...

Answer 12

There are a few things that can cause your Dexter Electric Over Hydraulic Actuator #K71-651 to run none stop. The most likely reason is an issue with your break away switch. If the break away switch is faulty that would cause the actuator to think…

view full answer...