Recommended Trailer Jack to Replace Shelby Model 5854AV Sidewind Jack

Question

Question:

Do you have a product that can replace a Shelby Industries 5854AV-83GF trailer jack? Thanks for your help

asked by: Danny

0

Expert Reply:

For a similar sidewind trailer jack to your existing Shelby model jack, I recommend looking at the Dutton-Lainson Trailer Jack # DL22300. This is a great swivel jack that will bolt to any trailer tongue that is up to 3 inches wide and 5 inches tall. It features a Zinc plated TUFFPLATE finish that will lead to a longer life and has a 10 inch lift with a weight capacity of 1,200 pounds. The mounting plate measures 6-3/4 inches x 5-3/4 inches and all the mounting hardware is included.

I have attached a couple of demonstration videos on this trailer jack so you can see exactly how it looks and operates.

expert reply by: Chris R

0

Answer 1

I checked the Dutton-Lainson website but a complete engineering diagram of this item is not available, so I took a piece from inventory and measured the mounting hole spacing. All eight mounting holes on the Dutton-Lainson Sidewind Swivel Jack…

view full answer...

Answer 2

The Dutton-Lainson #DL22300 is proudly made in the USA.

view full answer...

Answer 3

This particular Dutton-Lainson jack is made in China. Some of their other jacks are U.S. built. The Dutton-Lainson Model 6800, part #DL22580 is built in the U.S.

view full answer...

Answer 4

In order to remove a welded-on trailer tongue jack you will need to cut off the old welds to release the mounting bracket. This can be done using an angle grinder. The jack can then be replaced with another welded-on option such as the Fulton Marine…

view full answer...

Answer 5

Dutton Lainson makes a galvanized, USA-made swivel jack #DL22300 that can work attached to the side of the trailer tongue. This is a popular option for trailers that will see saltwater so it would work well for you. It has a tongue weight lifting…

view full answer...

Answer 6

I measured the Replacement Sidewind Handles #MJ-1000B-HD and #MJ-1500B-HD and found that they both have a diameter of 1/2" and part MJ-1000B-HD measures 2" from the end of the handle to the center of the pin hole while part MJ-1500B-HD…

view full answer...

Answer 7

In order to find if the mounting holes on the Swivel Marine Trailer Jack with Caster Wheel - Bolt On - Sidewind - 10" Travel - 1,000 lbs #DL84MR will line up with your existing bracket you will need to take some measurements. See the dimensional…

view full answer...

Answer 8

The Dutton Lainson jacks are all made in America. I attached a link to a page that has all of the Dutton Lainson trailer jacks we offer. A very popular option is the part #DL22300 which is made in America.

view full answer...

Answer 9

Sometimes a substitute part like a jack handle will fit on another brand of jack but we do not test items in this way since there are so many possible combinations. I did check the dimensions of an alternate handle, part #BD500171, and found that the…

view full answer...

Answer 10

The diameter of the Replacement Sidewind Handle #MJ-1000B-HD that you referenced is 1/2 inch. The radius of the handle is 7 inches.

view full answer...

Answer 11

The overall height of the Round Swivel Marine Jack w/ Wheel #MJ-1200B is 22-3/8 inches when fully retracted. It can swivel forward or back too.

view full answer...

Answer 12

Based on the picture you submitted the Fulton Marine Jack part #FXP100W0301 that you referenced would be exactly what you'd need and would bolt right up to the mount you have on the trailer frame.

view full answer...

Recommended Trailer Jack to Replace Shelby Model 5854AV Sidewind Jack

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching