Replacement Access Tonneau Cover and Velcro for Access TonnoSport # A22020199

Question

Question:

Do they make replacement vinyl for this cover A22020199

asked by: Chris R

0

Expert Reply:

I reached out to my contact at Access and the replacement cover is # A22020191. The replacement Velcro for the frame is the Replacement Velcro Strip for Access Tonneau Covers - 1" x 17' # A60270.

expert reply by: Jason S

0

Answer 1

We have the part #A30474 which is a 1-1/2 inch wide Velcro strip replacement for Access tonneau covers like what you have. The overall length is 17 feet but is designed to be cut down to size as needed.

view full answer...

Answer 2

Replacement Truxedo Shur-Bond Velcro Brand Fastener #TX1117876 is the same 1 inch width and it is the hook portion only just like #A60270 which is the Access replacement part. So it will fit its just that the 2 parts, the Tonneau cover and strip,…

view full answer...

Answer 3

The only difference between the Access Replacement Velcro Strips #A30474 and #A60270 is that A30474 is 1-1/2 inches wide and A60270 is only 1 inch wide. They are both 17 feet long and come with the 4 screws to help keep them in place.

view full answer...

Answer 4

We have the Velcro you need for your Access Tonneau cover for your 2012 F-150. For the hook portion that installs on the top rail you can use part #A60270 for the 17-ft long and 1-inch wide, and part #A30474 for the 17-ft long strip that is 1-1/2…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 11

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...