Weight Capacity of Fifth Wheel Rail Kits by Curt

Question

Question:

Hi there. quick question Im looking at 16443/204 and I was wondering if there is a weight limit on this material or can I install anyone of the 5th wheel hitch on this thank you

asked by: Rich

0

Expert Reply:

With fifth wheel rail kits our manufacturers state that the rails will have the same ratings as whatever hitch is installed in them. This means the rails are rated higher than basically any hitch that could fit them and the types of trucks they are designed to fit.

expert reply by: Jameson C

0

Answer 1

We have what you need and it will work with both hitches. You will not need to change the above bed rails for your 1999 Ford F-350 Super Duty if you install ISR (Industry Standard Rails) which pretty much the only currently available option. Any…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 4

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 5

Most fifth wheel rails are made to the same industry standard dimensions. They aren't all though. If you measure 22 inches on center between the two rails and they look like the rails of the #RP30035 that you referenced they would be the industry…

view full answer...

Answer 6

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth mentioning…

view full answer...

Answer 7

There are a couple of options that'll work great with your Lippert Turning Point Pin Box, however one hitch stands out to me more than others. Take a look at the: -Curt E16 5th Wheel Trailer Hitch - Slide Bar Jaw - 16,000 lbs #C16115 This 5th…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

The recommendation for the 10" diameter lube plate on a B&W Companion 5th Wheel Trailer has come from the manufacturer of the fifth wheel hitch, B&W. The Lube Plate for Reese 5th Wheel Trailer Hitches part #RP83002 will work just fine…

view full answer...

Answer 10

You do not have to use a sliding 5th wheel hitch in a short bed truck. In many cases, truck beds shorter than 8 ft do not have enough clearance between the trailer and truck to execute sharp turns. This is why sliding hitches were invented. Due to…

view full answer...

Answer 11

The mounting holes in the No-Drill Mount Kit #F2530 don't line up perfectly to mount the Air Command II Xtreme Duty Compressor #F2549, but they are close enough that you can widen the holes a bit to accommodate the compressor and avoid drilling…

view full answer...

Answer 12

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...