Recommended Trailer Hitch Receiver For 1989 Ford E-150 With Step Bumper

Question

Question:

Hi, I have an 1989 Ford E150 van with a step bumper. What hitch can you recommend, Class 3 or 4, that will be flush with the bumper, and not hide underneath where I cant get to it? Thanks

asked by: Nick

0

Expert Reply:

For your 1989 Ford E-150 van with step bumper, I recommend the Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" # 75703. This will give you a trailer hitch receiver that is close to flush with your step bumper for easy access. I've attached a photo to assist in the look and a video to assist in the installation.

If you don't already have the trailer wiring, I recommend the 4-Pole Hardwire Kit with Circuit Tester # 18252 which will allow you to hardwire your connections quickly and easily.

For a ball mount, I recommend the B&W Tow & Stow 2-Ball Mount - 2" Hitch - 5" Drop, 5-1/2" Rise - 10K - Black # BWTS10037B. This will give you an adjustable mount to tow multiple trailers level. It also has two integrated hitch balls to fit a 2 inch coupler or a 2-5/16 inch coupler. This ball mount has a really nice and clean looking stow away option that will protect your shins when not in use. I recommend using a hitch lock like # e98882 to protect your investment.

expert reply by: Jason S

0

click to enlarge

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 3

Hey Michael, thanks for reaching out! The EcoHitch #EH57FR sits a little higher than the Curt #C52NR so it will give you better ground clearance for your 2024 Chevy Silverado 2500. The EcoHitch is a bit more recessed into the front bumper than the…

view full answer...

Answer 4

For your 2003 Ford E-350 with a step bumper, the Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" #75703 will fit well. I've attached a photo of a step bumper fit to assist. I've also attached a video install of a…

view full answer...

Answer 5

The AL-KO company was bought out by Dexter, so he may have been thinking Dexter axles which the #K23-478-00 and #K23-479-00 would fit with the 4 bolt mounting pattern. The K23-538-00 and K23-539-00 are the correct ones for the AL-KO T-44 axle, as you…

view full answer...

Answer 6

I attached a picture that shows the Curt hitch part #C77VV installed on a Hornet to show you where the hitch opening will sit once installed. It does fit right to the bottom of the rear bumper.

view full answer...

Answer 7

The notches on this hitch #14053 are not designed to fit around the rivets. Rather the hitch flange will sit directly below the rivets. This hardware kit includes steel spacers which go between the frame and the hitch. These allow the hitch it be…

view full answer...

Answer 8

I can help you pick out the correct hub, but we don't have a cross-reference part number for the one you listed. In order to pick out the correct hub assembly for a trailer you are going to need know a few key pieces of information. The first…

view full answer...

Answer 9

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 10

I went to our warehouse and took a couple of measurements of the part #C15800. I have attached a photo of the trailer hitch and it has the dimensions noted. It measures 7 inches from the mounting lip to the top of the receiver opening and 9-1/2…

view full answer...