Comparing Curt Trailer Hitch # C11085 and # 11496 for a 2008 Honda Accord

Question

Question:

Im trying to decide on which hitch to get for my 2008 Honda Accord LX sedan 4 cyl. Ive narrowed it down to the 2 Curt models available 11496 and C11085. Aside from the aesthetic differences between these two and the price difference, why should I get one over the other? Thank you.

asked by: David

0

Expert Reply:

The differences between Curt Trailer Hitch # C11085 and # 11496 are so few, it really only comes down to aesthetics. Both hitches have the same capacity, they install the same way, and they both come with a ball mount, pin and clip. Besides price, the only differences is in the cross tubing. Trailer hitch # 11496 is at a direct angle while # C11085 is more of a gentle curve. A lot of people want as much of the hitch hidden as possible so I would go with # 11496. I have included a link to the installation details for you to view.

If you plan on doing some towing, the hitch comes with a ball mount and you can use ball # 19256 (1-7/8 inch diameter) or # 19258 (2 inch diameter). For trailer wiring, use # 118420.

If you plan to use the rack for a bike rack or other non-trailer loads, in order to be in compliance with Curt warranty requirements, all non-trailer loads must be secured with a stabilization strap like # 18050. The Curt hitches are the only ones that one this requirement.

expert reply by: Michael H

0

Answer 1

Both Curt trailer hitch receivers that fit your 2009 Honda Accord, parts #C11496 and #C11085, are Class I hitches that measure 1-1/4 inches. They also have the same towing and tongue weight capacities. They even install in the same location and…

view full answer...

Answer 2

The type of trailer hitch that is offered for your 2009 Honda Accord 4-door sedan is a light-duty 1-1/4-inch Class I type. A Class I hitch has sufficient strength to handle the weight of only 2 bikes. The linked article on hitch classes will give you…

view full answer...

Answer 3

Both hitches are a confirmed fit for your Accord. The only difference between the two hitches you mentioned, the #C11085 and the #C11496 is that the #C11085 fits against the underside of the vehicle more cleanly. It wraps around the spare tire well,…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 8

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 11

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 12

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Comparing Curt Trailer Hitch # C11085 and # 11496 for a 2008 Honda Accord

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching