Dimensions of Surco Stand-off Brace

Question

Question:

What is the total length of this part? We have a 2000 Newmar Dutch Star DP which needs two new arms that attach the ladder to the back of the MH. Do not know who the original ladder manufacturer as that provided the rear ladder to Newmar for our Dutch Star.

asked by: Mike M

1

Helpful Expert Reply:

The Replacement Stand-Off Brace for Surco Universal Exterior RV Ladders # SPN-416 measures 5 inches in length and has a diameter of 1 inch.

expert reply by: Kyle S

1

Answer 1

I went out into our warehouse and measured the Replacement Stand-Off Brace #SPN-416 and found that it measures 5-1/2 inches. This is the only standoff tube we offer at this time.

view full answer...

Answer 2

The base on the Replacement Stand-Off Brace for the Surco Universal Exterior RV Ladders #SPN-416 slides over the standoff tube and is held back with the lip formed by the end of the tube because the tube is widened at the other end. The base is then…

view full answer...

Answer 3

We have replacement stand-off or insert nuts for RV ladders but none that are made specifically for a motor home as each piece of hardware used on motor homes is not available in a data base. If by chance you have an aftermarket ladder, the Stromberg…

view full answer...

Answer 4

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 5

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 9

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 10

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Answer 11

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 12

You can get a new brake mounting flange for your axle. The old flange will need to be cut off. The part is #4-44-1. This is designed to fit a 3 inch trailer axle and should be welded in place by a professional. Since you would also have to get the…

view full answer...

Dimensions of Surco Stand-off Brace

Product Page this Question was Asked From

Continue Researching